[Asterisk-Users] my zap channel not ringing & source from

yusuf at ecntelecoms.com yusuf at ecntelecoms.com
Thu Mar 2 13:00:04 MST 2006


Ok,

to change signalling/timing of card, make changes to wanpipe*.conf,
probably /etc/wanpipe/wanpipe1.conf.

try playing around with CRC, CLOCKING, etc.
> Yes, I think I made a progress,
>
> I got this from my pri status, but my sync source is till saying
> "internally
> blocked" I have made several attempt at changing it to line but no success
> yet.
>
> How can I change my clock source from internal to telco line
>
> My debugs are as follows:
>
> gnugk*CLI> pri show span 1
> Primary D-channel: 16
> Status: Provisioned, Up, Active
> Switchtype: EuroISDN
> Type: CPE
> Window Length: 0/7
> Sentrej: 0
> SolicitFbit: 0
> Retrans: 0
> Busy: 0
> Overlap Dial: 0
> T200 Timer: 1000
> T203 Timer: 10000
> T305 Timer: 30000
> T308 Timer: 4000
> T313 Timer: 4000
> N200 Counter: 3
>
>
>
> gnugk*CLI> pri intense debug spanX
> < [ 02 01 7f ]
>
> < Unnumbered frame:
> < SAPI: 00  C/R: 1 EA: 0
> <  TEI: 000        EA: 1
> <   M3: 3   P/F: 1 M2: 3 11: 3  [ SABME (set asynchronous balanced mode
> extended) ]
> < 0 bytes of data
> -- Got SABME from network peer.
> Sending Unnumbered Acknowledgement
>
>> [ 02 01 73 ]
>
>> Unnumbered frame:
>> SAPI: 00  C/R: 1 EA: 0
>>  TEI: 000        EA: 1
>>   M3: 3   P/F: 1 M2: 0 11: 3  [ UA (unnumbered acknowledgement) ]
>> 0 bytes of data
> -- Restarting T203 counter
> -- Restarting T203 counter
>   == Primary D-Channel on span 1 up
>     -- Accepting AUTHENTICATED call from 10.80.1.151:
>        > requested format = ulaw,
>        > requested prefs = (),
>        > actual format = gsm,
>        > host prefs = (),
>        > priority = mine
>     -- Executing Answer("IAX2/marko-3", "") in new stack
>     -- Executing Dial("IAX2/marko-3", "Zap/g1/6210006|60|Ttr") in new
> stack
>     -- Requested transfer capability: 0x00 - SPEECH
>
>> [ 00 01 00 00 08 02 00 0a 05 04 03 80 90 a3 18 03 a9 83 81 6c 07 21 81
>> 31
> 31 31 31 31 70 08 a1 36 32 31 30 30 30 36 a1 ]
>
>> Informational frame:
>> SAPI: 00  C/R: 0 EA: 0
>>  TEI: 000        EA: 1
>> N(S): 000   0: 0
>> N(R): 000   P: 0
>> 35 bytes of data
> -- Restarting T203 counter
> Stopping T_203 timer
> Starting T_200 timer
>> Protocol Discriminator: Q.931 (8)  len=35
>> Call Ref: len= 2 (reference 10/0xA) (Originator)
>> Message type: SETUP (5)
>> [04 03 80 90 a3]
>> Bearer Capability (len= 5) [ Ext: 1  Q.931 Std: 0  Info transfer
> capability: Speech (0)
>>                              Ext: 1  Trans mode/rate: 64kbps,
>> circuit-mode
> (16)
>>                              Ext: 1  User information layer 1: A-Law
>> (35)
>> [18 03 a9 83 81]
>> Channel ID (len= 5) [ Ext: 1  IntID: Implicit, PRI Spare: 0, Exclusive
> Dchan: 0
>>                        ChanSel: Reserved
>>                       Ext: 1  Coding: 0   Number Specified   Channel
>> Type:
> 3
>>                       Ext: 1  Channel: 1 ]
>> [6c 07 21 81 31 31 31 31 31]
>> Calling Number (len= 9) [ Ext: 0  TON: National Number (2)  NPI:
> ISDN/Telephony Numbering Plan (E.164/E.163) (1)
>>                           Presentation: Presentation permitted, user
> number passed network screening (1) '11111' ]
>> [70 08 a1 36 32 31 30 30 30 36]
>> Called Number (len=10) [ Ext: 1  TON: National Number (2)  NPI:
> ISDN/Telephony Numbering Plan (E.164/E.163) (1) '6210006' ]
>> [a1]
>> Sending Complete (len= 1)
>     -- Called g1/6210006
> gnugk*CLI> pri intense debug spanX
> < [ 02 01 7f ]
>
> < Unnumbered frame:
> < SAPI: 00  C/R: 1 EA: 0
> <  TEI: 000        EA: 1
> <   M3: 3   P/F: 1 M2: 3 11: 3  [ SABME (set asynchronous balanced mode
> extended) ]
> < 0 bytes of data
> -- Got SABME from network peer.
> Sending Unnumbered Acknowledgement
>
>> [ 02 01 73 ]
>
>> Unnumbered frame:
>> SAPI: 00  C/R: 1 EA: 0
>>  TEI: 000        EA: 1
>>   M3: 3   P/F: 1 M2: 0 11: 3  [ UA (unnumbered acknowledgement) ]
>> 0 bytes of data
> -- Restarting T203 counter
>   == Primary D-Channel on span 1 up
> gnugk*CLI> pri intense debug spanX
>
>
> gnugk*CLI>
>> Informational frame:
>> SAPI: 00  C/R: 0 EA: 0
>>  TEI: 000        EA: 1
>> N(S): 000   0: 0
>> N(R): 000   P: 0
>> 35 bytes of data
> -- Restarting T203 counter
> Stopping T_203 timer
> Starting T_200 timer
>> Protocol Discriminator: Q.931 (8)  len=35
>> Call Ref: len= 2 (reference 12/0xC) (Originator)
>> Message type: SETUP (5)
>> [04 03 80 90 a3]
>> Bearer Capability (len= 5) [ Ext: 1  Q.931 Std: 0  Info transfer
> capability: Speech (0)
>>                              Ext: 1  Trans mode/rate: 64kbps,
>> circuit-mode
> (16)
>>                              Ext: 1  User information layer 1: A-Law
>> (35)
>> [18 03 a9 83 81]
>> Channel ID (len= 5) [ Ext: 1  IntID: Implicit, PRI Spare: 0, Exclusive
> Dchan: 0
>>                        ChanSel: Reserved
>>                       Ext: 1  Coding: 0   Number Specified   Channel
>> Type:
> 3
>>                       Ext: 1  Channel: 1 ]
>> [6c 07 21 81 31 31 31 31 31]
>> Calling Number (len= 9) [ Ext: 0  TON: National Number (2)  NPI:
> ISDN/Telephony Numbering Plan (E.164/E.163) (1)
>>                           Presentation: Presentation permitted, user
> number passed network screening (1) '11111' ]
>> [70 08 a1 36 32 31 30 30 30 34]
>> Called Number (len=10) [ Ext: 1  TON: National Number (2)  NPI:
> ISDN/Telephony Numbering Plan (E.164/E.163) (1) '6210004' ]
>> [a1]CLI>
>> Sending Complete (len= 1)
>     -- Called g1/6210004
> gnugk*CLI>
>
>
> I have changed the extension.conf as advised.
>
> goksie
>
>
>
>
>
>
> -----Original Message-----
> From: asterisk-users-bounces at lists.digium.com
> [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of yusuf
> Sent: Thursday, March 02, 2006 6:41 PM
> To: Asterisk Users Mailing List - Non-Commercial Discussion
> Subject: Re: [Asterisk-Users] my zap channel not ringing
>
> ADEGOKE ARUNA wrote:
>>
>> I need your help
>>
>> I have a sangoma A104D on my dell server; I got card status ok with no
> alarm
>> If I dialed the extension 6210006, it shows the output as stated below,
> but
>> there is no ringing from the pstn number nor the iax softphone am using
>> on
>> my pc.
>>
>> I will be glad if someone can give me a working config?
>>
>> What I want to achieve is to send all my call to the pstn on A104D?
>>
>> The pstn am talking to is alcatel S12 and the pri status on their switch
> is
>> showing the channel is external blocked meaning that the channels are
>> blocked from my asterisk box.
>> .
>>
>>
>> Output from asterisk cli
>>
>> -- Accepting AUTHENTICATED call from 10.80.1.151:
>>        > requested format = ulaw,
>>        > requested prefs = (),
>>        > actual format = gsm,
>>        > host prefs = (),
>>        > priority = mine
>>     -- Executing Answer("IAX2/marko-3", "") in new stack
>>     -- Executing Dial("IAX2/marko-3", "Zap/g1/6210006,60,r") in new
>> stack
>>     -- Called g1/6210006,60,r
>>     -- Zap/1-1 answered IAX2/marko-3
>>     -- Hungup 'Zap/1-1'
>>   == Spawn extension (default, 6210006, 2) exited non-zero on
> 'IAX2/marko-3'
>>     -- Hungup 'IAX2/marko-3'
>>
>> Extension.conf (extract)
>>
>> exten => _621XXXX,1,Answer()
>> exten => _621XXXX,n,Dial,Zap/g1/${EXTEN),60,r
>> ;exten => _621XXXX,n,Voicemail(u${EXTEN})
>> exten => _621XXXX,n,Hangup()
>>
>> Zaptel.conf
>>
>> span=1,1,0,ccs,hdb3,crc4
>> span=1,2,0,ccs,hdb3,crc4
>> span=1,3,0,ccs,hdb3,crc4
>> span=1,4,0,ccs,hdb3,crc4
>> bchan = 1-15, 17-31, 32-46, 48-62, 63-77, 79-93, 94-108, 110-124
>> dchan = 16, 47, 78, 109
>>
>> Zapata.conf
>>
>> [channels]
>> language=en
>> context=default
>> switchtype=qsig
>> signalling=pri_cpe
>> usecallerid=yes
>> hidecallerid=no
>> callwaiting=yes
>> usecallingpres=yes
>> callwaitingcallerid=yes
>> threewaycalling=yes
>> transfer=yes
>> canpark=yes
>> cancallforward=yes
>> callreturn=yes
>> echocancel=yes
>> echocancelwhenbridged=yes
>> rxgain=0.0
>> txgain=0.0
>> group=1
>> channel =>1-15, 17-31
>> ;callgroup=1
>> ;pickupgroup=1
>> immediate=no
>> ;callerid=6216000
>> ; signalling = pri_cpe
>> group = 2
>> channel => 32-46, 48-62
>>
>> group = 3
>> channel => 63-77, 79-93
>>
>> group = 4
>> channel => 94-108, 110-124
>>
>>
>>
>> the channel status
>>
>> *CLI> zap show status
>> Description                              Alarms     IRQ        bpviol
>> CRC4
>> wanpipe1 card 0                          OK         0          0
> 0
>> wanpipe2 card 1                          RED        0          0
> 0
>> wanpipe3 card 2                          RED        0          0
> 0
>> wanpipe4 card 3                          RED        0          0
> 0
>>
>>
>>
>> 1 19:33:14 NOTICE[17314]: chan_zap.c:6342 handle_init_event: Alarm
>> cleared
>> on channel 1
>> Mar  1 19:33:14 NOTICE[17314]: chan_zap.c:6342 handle_init_event: Alarm
>> cleared on channel 2
>> Mar  1 19:33:14 NOTICE[17314]: chan_zap.c:6342 handle_init_event: Alarm
>> cleared on channel 3
>> Mar  1 19:33:14 NOTICE[17314]: chan_zap.c:6342 handle_init_event: Alarm
>> cleared on channel 4
>> Mar  1 19:33:14 NOTICE[17314]: chan_zap.c:6342 handle_init_event: Alarm
>> cleared on channel 5
>> Mar  1 19:33:14 NOTICE[17314]: chan_zap.c:6342 handle_init_event: Alarm
>> cleared on channel 6
>> Mar  1 19:33:14 NOTICE[17314]: chan_zap.c:6342 handle_init_event: Alarm
>> cleared on channel 7
>> Mar  1 19:33:14 NOTICE[17314]: chan_zap.c:6342 handle_init_event: Alarm
>> cleared on channel 8
>> Mar  1 19:33:14 NOTICE[17314]: chan_zap.c:6342 handle_init_event: Alarm
>> cleared on channel 9
>> Mar  1 19:33:14 NOTICE[17314]: chan_zap.c:6342 handle_init_event: Alarm
>> cleared on channel 10
>> Mar  1 19:33:14 NOTICE[17314]: chan_zap.c:6342 handle_init_event: Alarm
>> cleared on channel 11
>> For all the 31 channels
>>
>> goksie
> Hi,
>
> maybe this is just been pedantic but why do you answer the channel
> first, you dont use IVR, so why answer it. and use dial like this:
>
> exten => _621XXXX,1,Dial(Zap/g1/${EXTEN),60,r)
>
> everything else looks good though, it should work.  I also have a
> sangoma A104D.
>
> also, should'nt be (could be wrong, but i have it like this):
>
>   span=1,1,0,ccs,hdb3,crc4
>   span=2,2,0,ccs,hdb3,crc4
>   span=3,3,0,ccs,hdb3,crc4
>   span=4,4,0,ccs,hdb3,crc4
>   bchan = 1-15, 17-31, 32-46, 48-62, 63-77, 79-93, 94-108, 110-124
>   dchan = 16, 47, 78, 109
>
>
>
> yusuf
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>
> --
> This message has been scanned for viruses and
> dangerous content by MailScanner, and is
> believed to be clean.
>
>



-- 
This message has been scanned for viruses and
dangerous content by MailScanner, and is
believed to be clean.




More information about the asterisk-users mailing list