[asterisk-users] Zaptel Problem - Unable to create channel of type 'Zap'

[Moises Silva]

Are you sure the other end is configured properly?
What does "zttool" says?
Have you turned on all the asterisk debug messages to look further?

Regards

On 7/19/06, Lincoln Zuljewic Silva <lsilva at corsidian.com> wrote:
>
>  Hello all. I have a Digitum TE110P board configured and working (I think
> that it's working). When I configure in extensions.conf to a extension route
> to that board I get "Unable to create channel of type 'Zap'" on log.
>
>  Here are some configuration:
>
>  lspci -vv
>  0000:01:07.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN
> interface
>          Subsystem: Unknown device 795e:0001
>          Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
>          Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
>          Latency: 64 (250ns min, 32000ns max)
>          Interrupt: pin A routed to IRQ 11
>          Region 0: I/O ports at c800 [size=256]
>          Region 1: Memory at fc5ff000 (32-bit, non-prefetchable) [size=4K]
>          Capabilities: [40] Power Management version 2
>                  Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA
> PME(D0+,D1-,D2+,D3hot+,D3cold-)
>                  Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
>  ztcfg -vv
>  Zaptel Configuration
>  ======================
>
>  SPAN 1: CAS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)
>
>  Channel map:
>
>  Channel 01: Individual Clear channel (Default) (Slaves: 01)
>  Channel 02: Individual Clear channel (Default) (Slaves: 02)
>  Channel 03: Individual Clear channel (Default) (Slaves: 03)
>  Channel 04: Individual Clear channel (Default) (Slaves: 04)
>  Channel 05: Individual Clear channel (Default) (Slaves: 05)
>  Channel 06: Individual Clear channel (Default) (Slaves: 06)
>  Channel 07: Individual Clear channel (Default) (Slaves: 07)
>  Channel 08: Individual Clear channel (Default) (Slaves: 08)
>  Channel 09: Individual Clear channel (Default) (Slaves: 09)
>  Channel 10: Individual Clear channel (Default) (Slaves: 10)
>  Channel 11: Individual Clear channel (Default) (Slaves: 11)
>  Channel 12: Individual Clear channel (Default) (Slaves: 12)
>  Channel 13: Individual Clear channel (Default) (Slaves: 13)
>  Channel 14: Individual Clear channel (Default) (Slaves: 14)
>  Channel 15: Individual Clear channel (Default) (Slaves: 15)
>  Channel 16: D-channel (Default) (Slaves: 16)
>  Channel 17: Individual Clear channel (Default) (Slaves: 17)
>  Channel 18: Individual Clear channel (Default) (Slaves: 18)
>  Channel 19: Individual Clear channel (Default) (Slaves: 19)
>  Channel 20: Individual Clear channel (Default) (Slaves: 20)
>  Channel 21: Individual Clear channel (Default) (Slaves: 21)
>  Channel 22: Individual Clear channel (Default) (Slaves: 22)
>  Channel 23: Individual Clear channel (Default) (Slaves: 23)
>  Channel 24: Individual Clear channel (Default) (Slaves: 24)
>  Channel 25: Individual Clear channel (Default) (Slaves: 25)
>  Channel 26: Individual Clear channel (Default) (Slaves: 26)
>  Channel 27: Individual Clear channel (Default) (Slaves: 27)
>  Channel 28: Individual Clear channel (Default) (Slaves: 28)
>  Channel 29: Individual Clear channel (Default) (Slaves: 29)
>  Channel 30: Individual Clear channel (Default) (Slaves: 30)
>  Channel 31: Individual Clear channel (Default) (Slaves: 31)
>
>  31 channels configured.
>
>  My zaptel.cfg
>  span=1,0,0,cas,hdb3
>  loadzone=us
>  defaultzone=us
>  bchan=1-15,17-31
>  dchan=16
>
>  My zapata.conf
>  [channels]
>  context=customer
>  signalling=pri_cpe
>  channel => 1
>
>  My extensions.conf
>  exten => 4502,1,Dial(Zap/1/4502)
>
>  show channels in Asterisk CLI:
>          Channel  (Context    Extension    Pri )   State Appl.         Data
>  0 active channel(s)
>
>  zap show channels in Asterisk CLI:
>     Chan Extension  Context         Language   MusicOnHold
>   pseudo            customer
>        1            customer
>
>  zap show channel 1 in Asterisk CLI:
>  hannel: 1>
>  File Descriptor: 10
>  Span: 1
>  Extension:
>  Dialing: no
>  Context: corsidian
>  Caller ID string:
>  Destroy: 0
>  InAlarm: 0
>  Signalling Type: PRI Signalling
>  Owner: <None>
>  Real: <None>
>  Callwait: <None>
>  Threeway: <None>
>  Confno: -1
>  Propagated Conference: -1
>  Real in conference: 0
>  DSP: no
>  Relax DTMF: no
>  Dialing/CallwaitCAS: 0/0
>  Default law: alaw
>  Fax Handled: no
>  Pulse phone: no
>  Echo Cancellation: 0 taps unless TDM bridged, currently OFF
>  PRI Flags:
>  PRI Logical Span: Implicit
>  Actual Hookstate: Onhook
>
>  When I dial 4502 in the softphone I get "Unable to create channel of type
> 'Zap'".
>  Could anybody give to me a little help ?
>
>  Thanks a lot !
>  Lincoln
>
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>
> http://lists.digium.com/mailman/listinfo/asterisk-users
>
>
>


-- 
"Su nombre es GNU/Linux, no solamente Linux, mas info en http://www.gnu.org"