[Asterisk-Users] Analog with channel bank - Inbound works, outbound doesn't

james.texter at cox.net james.texter at cox.net
Wed Feb 1 12:50:14 MST 2006


No, it's an Access Bank II SNMP.

Thanks,

James

C F wrote:
> Is this an Adit 600?
>
> On 2/1/06, james.texter at cox.net <james.texter at cox.net> wrote:
>> The output from the CLI when I put in an inbound call is the following:
>>
>>    -- Starting simple switch on 'Zap/25-1'
>>    -- Executing GotoIf("Zap/25-1", "1?from-pstn-reghours|s|1:") in new stack
>>    -- Goto (from-pstn-reghours,s,1)
>>    -- Executing GotoIf("Zap/25-1", "0?from-pstn-reghours-nofax|s|1:2") in new stack
>>    -- Goto (from-pstn-reghours,s,2)
>>    -- Executing Answer("Zap/25-1", "") in new stack
>>    -- Executing Wait("Zap/25-1", "1") in new stack
>>    -- Executing SetVar("Zap/25-1", "intype=EXT-412") in new stack
>>    -- Executing Cut("Zap/25-1", "intype=intype|-|1") in new stack
>>
>> It then goes on to call the extension I have setup.  I think it's coming in on Channel 25, but I'm not sure what the -1 is for in Zap/25-1.
>>
>> Not sure if this is relevant or not, but I'm using a Carrier Access Corporation (CAC) channel bank, with 1 FXO card and 1 FXS card.  The analog line is definitely hooked to the FXO card, and I definitely have the T1 plugged in to the FXO card.
>>
>> Thanks,
>>
>> James
>>
>>
>> C F wrote:
>>> Looks like  channel 25 is not the one hooked up to your POTS, when an
>>> incoming call arrives, what channel does the CLI report?
>>>
>>>
>>> On 2/1/06, james.texter at cox.net <james.texter at cox.net> wrote:
>>>> Thanks for the reply.  I have tried adding anywhere between 1 and 6 w's to the dial string, but still no luck.  I hooked up and listened on the line when the call went out, and never heard any DTMF's.  I'm sure this must be something simple, I just can't seem to figure out for the life of me what it is.  What other information can I provide to help sort this out?
>>>>
>>>> Thanks again,
>>>> James
>>>>
>>>> ------------------------------
>>>> You could insert a pause by adding a w before the number to be dialed,
>>>> like this:
>>>> Dial(zap/25/w1234567890) iirc each w puts a 500ms pause.
>>>>
>>>>
>>>> On 1/30/06, james.texter at cox.net <james.texter at cox.net> wrote:
>>>>>> I am experimenting with an asterisk setup in my office.  The last bit I have to test is working with analog lines.  I have TE411p digium card, with an ISDN line plugged into the first, a channel bank plugged into the second port, and the last two ports empty.  I have the following setup in my zaptel.conf:
>>>>>>
>>>>>> span=1,1,0,esf,b8zs
>>>>>> bchan=1-23
>>>>>> dchan=24
>>>>>>
>>>>>> span=2,0,0,d4,ami
>>>>>> fxsks=25
>>>>>>
>>>>>> And in zapata.conf, I have:
>>>>>> group=2
>>>>>> language=en
>>>>>> context=from-pstn
>>>>>> signalling=fxs_ks
>>>>>> channel=>25
>>>>>>
>>>>>> I have one analog line plugged in for testing.  If I dial that analog number, the inbound call arrives, and it works great.  However, when I place an outbound call, I get the following output:
>>>>>> -- Called g2/5148346
>>>>>> -- Zap/25-1 answered SIP/412-9b72
>>>>>>
>>>>>> However, my number never rings.  After about 30 seconds, I get a message saying my call could not be completed as dialed.  Almost like it didn't get all of the digits.  Is there a way to inject a pause before dialing?  Any other thoughts?  Any help is greatly appreciated.
>>>>>>
>>>>>> _______________________________________________
>>>>>> --Bandwidth and Colocation provided by Easynews.com --
>>>>>>
>>>>>> Asterisk-Users mailing list
>>>>>> To UNSUBSCRIBE or update options visit:
>>>>>>    http://lists.digium.com/mailman/listinfo/asterisk-users
>>>>>>
>>>> _______________________________________________
>>>> --Bandwidth and Colocation provided by Easynews.com --
>>>>
>>>> Asterisk-Users mailing list
>>>> To UNSUBSCRIBE or update options visit:
>>>>    http://lists.digium.com/mailman/listinfo/asterisk-users
>>>>
>>>>
>>>> _______________________________________________
>>>> --Bandwidth and Colocation provided by Easynews.com --
>>>>
>>>> Asterisk-Users mailing list
>>>> To UNSUBSCRIBE or update options visit:
>>>>    http://lists.digium.com/mailman/listinfo/asterisk-users
>>>>
>>> _______________________________________________
>>> --Bandwidth and Colocation provided by Easynews.com --
>>>
>>> Asterisk-Users mailing list
>>> To UNSUBSCRIBE or update options visit:
>>>    http://lists.digium.com/mailman/listinfo/asterisk-users
>>>
>>
>> _______________________________________________
>> --Bandwidth and Colocation provided by Easynews.com --
>>
>> Asterisk-Users mailing list
>> To UNSUBSCRIBE or update options visit:
>>   http://lists.digium.com/mailman/listinfo/asterisk-users
>>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>





More information about the asterisk-users mailing list