[Asterisk-Users] Diva Server BRI echo options (fixed)

[Giuseppe]

Hi, thanks to you all!
Finally echo cancellation works correctly on my card (eicon diva server 
4/bri)
Armin, that fixed the problem, thanks again!

Giuseppe


Armin Schindler ha scritto:

>Which version of divas driver do you use?
>
>If it's the v2 driver (from melware.de or in-kernel 2.6), then you need to 
>set
>  echocancelold=yes
>
>in the interfaces sections.
>
>If you use the new driver v3 (Eicon source RPM), 
>echocancelold=yes may not be set.
>
>Armin
>
>On Mon, 3 Apr 2006, Giuseppe wrote:
>  
>
>>Thanks Avi Miller!
>>
>>Here it is my capi.conf file
>>
>>[general]
>>nationalprefix=039
>>;;internationalprefix=011
>>rxgain=1.0
>>txgain=2.0
>>alaw=yes ;
>>
>>[ISDN3]             ;this example interface gets name 'ISDN1' and may be any
>>ntmode=yes             ;if isdn card operates in nt mode, set this to yes when
>>using NT-mode, ptp should be set in any case
>>incomingmsn=*             ;allow incoming calls to this list of MSNs/DIDs, *
>>== any
>>controller=3             ;capi controller number to use
>>group=1                ;dialout group
>>;softdtmf=on             ;enable/disable software dtmf detection, recommended
>>for AVM cards
>>;relaxdtmf=on             ;in addition to softdtmf, you can use relaxed dtmf
>>detection
>>;accountcode=             ;Asterisk accountcode to use in CDRs
>>context=isdn3in         ;context for incoming calls
>>holdtype=local             ;If set to 'hold', when Asterisk puts the call on
>>hold, ISDN HOLD will be used.
>>immediate=yes             ;immediate start of pbx with extension 's' if no
>>digits were received on incoming call (no destination number yet)
>>;echosquelch=1             ;_VERY_PRIMITIVE_ echo suppression
>>echocancel=yes             ;EICON DIVA SERVER (CAPI) echo cancelation
>>(possible values: 'no', 'yes', 'force', 'g164', 'g165')
>>;echocancelold=yes        ;use facility selector 6 instead of correct 8
>>(necessary for older eicon drivers)
>>echotail=64             ;echo cancel tail setting
>>bridge=yes             ;native bridging (CAPI line interconnect) if available
>>callgroup=1             ;Asterisk call group
>>;deflect=1234567         ;deflect incoming calls to 1234567 if all B channels
>>are busy
>>devices=2             ;number of concurrent calls on this controller (2 makes
>>sense for single BRI, 30 for PRI)
>>
>>Is there something wrong?
>>
>>Thanks again!
>>
>>Giuseppe
>>
>>Avi Miller ha scritto:
>>
>>    
>>
>>>Giuseppe wrote:
>>>
>>>      
>>>
>>>>I'm always getting this error when echo cancellation should start.
>>>>        
>>>>
>>>What does your /etc/asterisk/capi.conf look like?
>>>
>>>Also, have you configured your Eicon correctly? You may need to enable
>>>the Eicon web interface and check that each port is correct.
>>>
>>>      
>>>
>>_______________________________________________
>>--Bandwidth and Colocation provided by Easynews.com --
>>
>>Asterisk-Users mailing list
>>To UNSUBSCRIBE or update options visit:
>>http://lists.digium.com/mailman/listinfo/asterisk-users
>>
>>    
>>
>_______________________________________________
>--Bandwidth and Colocation provided by Easynews.com --
>
>Asterisk-Users mailing list
>To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>  
>