[Asterisk-Users] Re: cisco 3620 setup (newbie cisco alert)

[Asterisk]

Arrggh Nuts.

Don't suppose anyone has a spare NM-HDV hanging around that they want to 
sell ?

:(

Julian.

info at beprojects.com wrote:

> You need an NM-HDV card of some sort to run voice.  The WIC-1MFT-E1 
> can handle voice, but you still need the DSP's to use it as a voice 
> card. Putting that into an NM-HDV that has DSP's will make the voice 
> ports and dsp's show up.
>
>
> Asterisk wrote:
>
>> ok, I'm starting to get confused, you must be getting annoyed .. how 
>> do I add this voice-port ?
>>
>> Also, if I want to use * to handle all of the SIP internal calls, and 
>> cisco to handle to inbound and outbound isdn-32 PRI calls, what 
>> "feature set" of the IOS should I need ? What hardware on the cisco 
>> 3620 should I need ? I've got a PRI-1CE1U and a WIC-1MFT-E1 and a 
>> two-port fast ethernet. I also have a 2610 to play with if required :)
>>
>> Many thanks for your help. It is much appreciated. There is only so 
>> much a newbie can do without advice.
>>
>> Julian.
>>
>> barney wrote:
>>
>>> I can`t see voice-port in your configuration. Something like this:
>>>
>>> !
>>> voice-port 1/0:15            ; voice-port 1/0:15, if your D channel 
>>> is Serial1/0:15
>>> input gain -6
>>> output attenuation 14
>>> echo-cancel coverage 32
>>> echo-cancel suppressor
>>> cptone SK
>>> description E1
>>> bearer-cap Speech
>>> !
>>>
>>> If you configure voice-port, try again to configure dial-peer (port 
>>> x/y:15 command) and if you have DSPs in you box, you must see 
>>> something like this:
>>>
>>> SIP-3640#show voice dsp
>>>
>>> DSP  DSP             DSPWARE CURR  BOOT                         PAK 
>>> TX/RX
>>> TYPE NUM CH CODEC    VERSION STATE STATE   RST AI VOICEPORT TS 
>>> ABORT  PACK COUNT
>>> ==== === == ======== ======= ===== ======= === == ========= == ===== 
>>> ============
>>> C549 000 00 {high}    3.4.56 IDLE  idle      0  0 2/0:15    01     0 
>>> 0/16
>>>         01 {high}    3.4.56 IDLE  idle         0 2/0:15    17     0 0/0
>>> C549 001 00 {high}    3.4.56 IDLE  idle      0  0 2/0:15    02     0 
>>> 0/16
>>>         01 {high}    3.4.56 IDLE  idle         0 2/0:15    18     0 0/0
>>> ....
>>>
>>> If you don`t have any DSP in your C3620, it will be unusable. So 
>>> check it!
>>>
>>> -b
>>>
>>
>> _______________________________________________
>> Asterisk-Users mailing list
>> Asterisk-Users at lists.digium.com
>> http://lists.digium.com/mailman/listinfo/asterisk-users
>> To UNSUBSCRIBE or update options visit:
>>   http://lists.digium.com/mailman/listinfo/asterisk-users
>>
>> .
>>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>
>