[Asterisk-Users] Problem in Configuring Asterisk Server

Hemant Arora techxprt at gmail.com
Wed Mar 9 15:37:55 MST 2005


Hi ALL,

Below is what I did :

Installed FC3 , Zaptel Drivers , libpri, Asterisk.

E1 Card is - TE110P

When I run modprobe it gives me the output below:

Mar 10 04:18:26 asterisk kernel: ACPI: PCI interrupt 0000:00:0d.0[A]
-> GSI 11 (level, low) -> IRQ 11
Mar 10 04:18:26 asterisk kernel: Controller version: 24
Mar 10 04:18:26 asterisk kernel: FALC version: 00000000
Mar 10 04:18:26 asterisk kernel: TE110P: Setting up global serial
parameters for T1 FALC V1.2
Mar 10 04:18:26 asterisk kernel: TE110P: Successfully initialized
serial bus for card
Mar 10 04:18:26 asterisk kernel: Found a Wildcard: Digium Wildcard TE110P T1/E1
Mar 10 04:18:26 asterisk kernel: Registered tone zone 0 (United States
/ North America)
Mar 10 04:18:26 asterisk kernel: TE110P: Span configured for ESF/B8ZS
Mar 10 04:18:26 asterisk kernel: Calling startup (flags is 4099)
Mar 10 04:18:26 asterisk kernel: wcte1xxp: Setting yellow alarm

OutPut of  ztcfg -vv

Zaptel Configuration
======================

SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)

Channel map:

Channel 01: Individual Clear channel (Default) (Slaves: 01)
Channel 02: Individual Clear channel (Default) (Slaves: 02)
Channel 03: Individual Clear channel (Default) (Slaves: 03)
Channel 04: Individual Clear channel (Default) (Slaves: 04)
Channel 05: Individual Clear channel (Default) (Slaves: 05)
Channel 06: Individual Clear channel (Default) (Slaves: 06)
Channel 07: Individual Clear channel (Default) (Slaves: 07)
Channel 08: Individual Clear channel (Default) (Slaves: 08)
Channel 09: Individual Clear channel (Default) (Slaves: 09)
Channel 10: Individual Clear channel (Default) (Slaves: 10)
Channel 11: Individual Clear channel (Default) (Slaves: 11)
Channel 12: Individual Clear channel (Default) (Slaves: 12)
Channel 13: Individual Clear channel (Default) (Slaves: 13)
Channel 14: Individual Clear channel (Default) (Slaves: 14)
Channel 15: Individual Clear channel (Default) (Slaves: 15)
Channel 24: D-channel (Default) (Slaves: 24)

16 channels configured.

In zaptel.conf the entries are :

span=1,0,0,ccs,hdb3
bchan=1-15 # set this to 1-15,17-31 for E1
dchan=24 # set this to 16 for E1
loadzone = us
defaultzone=us

When I run asterisk it starts and gives me CLI> prompt.

But the card on the machine keeps flashing red light and I read
somewhere that it should show green light.

The Card is connected to CBR port on the router through simple RJ45
straight cable.

There are two questions I have :

1 - Why the card is flashing red and it should show green ? Just a not
on the router the CBR is also showing red even if i dont plug the wire
in.

2 - For E1 TE110P, What Config settings are needed in zaptel.conf and
/etc/asterisk/zapata.conf.?

Thanks for your help.



More information about the asterisk-users mailing list