[Asterisk-Users] EuroISDN Italy - quadbri - zaptel.conf - whatsettings work ?

[Robert Rozman]

Hi,

thanks for response....

I have following in zapata.conf, so I guess point to multipoint setting is 
right ?

Is framing and coding (ami,ccs) right for Italy ?

Thanks in advance,

regards,


Rob.

zapata.conf:

[channels]

switchtype = euroisdn

;pridialplan = dynamic je delalo
pridialplan = unknown
;prilocaldialplan = local
nationalprefix = 0
internationalprefix = 00
usecallingpres=yes

echocancel = yes
echocancelwhenbridged = yes
echotraining = 100
callerid=asreceived
overlapdial=yes

; p2mp TE mode (for connecting ISDN lines in point-to-multipoint mode)
signalling = bri_cpe_ptmp

context=from-isdn
group = 1

; S/T port 1-3 (first quadBRI, or lower ports of an octoBRI)
channel => 1-2
channel => 4-5
channel => 7-8
;------------------------------------------------------------------- 


----- Original Message ----- 
From: "Matteo Brancaleoni" <mbrancaleoni at espia.it>
To: "Asterisk Users Mailing List - Non-Commercial Discussion" 
<asterisk-users at lists.digium.com>
Sent: Thursday, June 09, 2005 10:45 AM
Subject: Re: [Asterisk-Users] EuroISDN Italy - quadbri - zaptel.conf - 
whatsettings work ?


> You're connected to a p2mp bri, switch to bri_cpe_p2mp
>
> Matteo.
>
> Il giorno mer, 08-06-2005 alle 19:54 +0200, Robert Rozman ha scritto:
>> Hi,
>>
>> I'm pulling my hair out, cause cannot connect to EuroISDN BRI in Italy 
>> with
>> octobri card from Beronet. I use bristuff and have following 
>> zaptel.conf...
>>
>> #
>> # This file is parsed by the Zaptel Configurator, ztcfg
>> #
>> #
>> # First come the span definitions, in the format
>> # span=<span num>,<timing>,<line build out
>> (LBO)>,<framing>,<coding>[,yellow]
>> #
>> # The timing parameter determines the selection of primary, secondary, 
>> and
>> # so on sync sources.  If this span should be considered a primary sync
>> # source, then give it a value of "1".  For a secondary, use "2", and so 
>> on.
>> # To not use this as a sync source, just use "0"
>> #
>> loadzone=it
>> defaultzone=it
>>
>> span=1,1,3,ccs,ami
>> span=2,0,3,ccs,ami
>> span=3,0,3,ccs,ami
>> span=4,0,3,ccs,ami
>> span=5,0,3,ccs,ami
>> span=6,0,3,ccs,ami
>> span=7,0,3,ccs,ami
>> span=8,0,3,ccs,ami
>>
>> bchan=1,2
>> dchan=3
>> bchan=4,5
>> dchan=6
>> bchan=7,8
>> dchan=9
>> bchan=10,11
>> dchan=12
>>
>> bchan=13,14
>> dchan=15
>> bchan=16,17
>> dchan=18
>> bchan=19,20
>> dchan=21
>> bchan=22,23
>> dchan=24
>>
>> I get this on bri intense debug...
>>
>>
>> > Unnumbered frame:
>> > SAPI: 63  C/R: 0 EA: 0
>> >  TEI: 127        EA: 1
>> >   M3: 0   P/F: 0 M2: 0 11: 3  [ UI (unnumbered information) ]
>> > 5 bytes of data
>> Sending TEI Request ri=64864
>>
>> > [ fc ff 03 0f fd 60 01 ff ]
>>
>> > Unnumbered frame:
>> > SAPI: 63  C/R: 0 EA: 0
>> >  TEI: 127        EA: 1
>> >   M3: 0   P/F: 0 M2: 0 11: 3  [ UI (unnumbered information) ]
>> > 5 bytes of data
>> Sending TEI Request ri=39384
>>
>> > [ fc ff 03 0f 99 d8 01 ff ]
>>
>> > Unnumbered frame:
>> > SAPI: 63  C/R: 0 EA: 0
>> >  TEI: 127        EA: 1
>> >   M3: 0   P/F: 0 M2: 0 11: 3  [ UI (unnumbered information) ]
>> > 5 bytes of data
>> Sending TEI Request ri=38343
>>
>> > [ fc ff 03 0f 95 c7 01 ff ]
>>
>> > Unnumbered frame:
>> > SAPI: 63  C/R: 0 EA: 0
>> >  TEI: 127        EA: 1
>> >   M3: 0   P/F: 0 M2: 0 11: 3  [ UI (unnumbered information) ]
>> > 5 bytes of data
>>
>>
>>
>> Thanks very much in advance,
>>
>> regards,
>>
>> Rob.
>>
>> _______________________________________________
>> Asterisk-Users mailing list
>> Asterisk-Users at lists.digium.com
>> http://lists.digium.com/mailman/listinfo/asterisk-users
>> To UNSUBSCRIBE or update options visit:
>>    http://lists.digium.com/mailman/listinfo/asterisk-users
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users