[Asterisk-Users] Re: Sangoma A102 cards testing FIXED

[Robert Augustyn]

May I ask what you did?
robert 

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Vikram
Rangnekar
Sent: Tuesday, February 15, 2005 1:59 PM
To: Asterisk Users Mailing List - Non-Commercial Discussion
Subject: [Asterisk-Users] Re: Sangoma A102 cards testing FIXED

Its fixed and working great.
> 
> I was working on the dma issue that nenad pointed out and when i tried 
> to hdparm -d 1 /dev/hda my harddisk i got a permissioned denied error 
> (I was root) So i started researching a bit more and realised that 
> since i have a sata hdd and running it in IDE mode i cant start dma so 
> i just recompiled the kernel with sata drivers and scsi activated then 
> i change the bio SATA setting to SATA ENHANCED (nothing else seems to 
> work) and changed the root=/dev/hda2 to
> root=/dev/sda2 in the kernel boot options and i was on my way. now 
> when i tierd hdparm -d 1 /dev/sda i was told that scsi dosent have dma 
> so it didnt matter.
> 
> Next i started the wanpipe drivers and started asterisk i didnt get 
> any errors so to test th config i used
> 
> exten => 111,1,Dial(Zap/g1/301)
> exten => 111,2,Hangup
> 
> and dialed that extension 111 and the extension 301 rang. i had 
> started pri intense debugging and used show channels to make sure the 
> call went over the e1 channels.
> 
> i'm still testing it, it seems to be working great right now only 
> error i got was a FCS BAD or somthing like that once.
> 
> My motherboard is a SuperMicro P4SCI just for your information.

+++ Vikram Rangnekar [13/02/05 13:01 +0100]:
> 
> Does anyone have any experience ith configureing the sangoma A102 card 
> for testing using a e1 cross cable i've configured and installed the 
> cards properly even the lights on the card are green which proves that 
> my cross cable is properly built too. my problem is with asterisk 
> which gives me these errors
> 
> PRI got event: HDLC Abort (6)on Primary D-channel of span 1 PRI got 
> event: HDLC Bad FCS (8) on Primary D-channel of span 2 No D-channels 
> available! Using Primary on channel anyways 47!
> PRI: !! Not good - head of queue has not been transmitted yet
> 
> 
> I've tried everything i can think off with the wancfg configuration 
> files here is my zaptel and zapata configs.
> 
> span=1,0,0,ccs,hdb3
> bchan=1-15
> dchan=16
> bchan=17-31
> 
> span=2,1,0,ccs,hdb3
> bchan=32-46
> dchan=47
> bchan=48-62
> 
> --------------------------
> zapata.conf
> 
> switchtype=euroisdn
> signalling=pri_net
> group=1
> channel=>1-15
> channel=>17-31
> 
> group=2
> signalling=pri_cpe
> channel=>32-46
> channel=>48-62
> -------------------------------
> do i need to fool around with some jumpers on the card or something to 
> activate internal clock on the card. zttol says INTERNALLY CLOCKED for 
> both the ports. There are NO Alarms and no missed IRQ's I'm using 
> asterisk 1.0.5 on debian with 2.4.29 kernel
> 
> --
> regards
> Vikram (http://www.vicramresearch.com) 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users

--
regards
Vikram (http://www.vicramresearch.com)
_______________________________________________
Asterisk-Users mailing list
Asterisk-Users at lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users