[Asterisk-Users] TDM400P FXO channel hookstate always "Offhook" &outbound digits sent before provider dialtone

[Tom Rymes]

Manny,

You are misinformed. My instructions were for A at H/AMP. If you opent he
configuration page for the ZAP trunk, you simply put "ww" as the
Outbound Dial Prefix, save the settings, and clikc in the red banner to
reload.

Manual changes only get overwritten if you make them by hand to the
extensions.conf or extensions_additional.conf. If you add your changes
to the extensions_custom.conf, they will not be overwritten by AMP.
(That's how I force my incoming Zap trunk to ring to a different place
than my incoming call settings.)

Tom 

> -----Original Message-----
> From: asterisk-users-bounces at lists.digium.com 
> [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of 
> Manny A. Wise
> Sent: Friday, August 12, 2005 5:16 PM
> To: 'Asterisk Users Mailing List - Non-Commercial Discussion'
> Subject: RE: [Asterisk-Users] TDM400P FXO channel hookstate 
> always "Offhook" &outbound digits sent before provider dialtone
> 
> 
> That's a good advice, BUT!!!!
> Remember we talking *@home here, it will get overwritten 
> every time you do a configuration reload... That is what I 
> did for my cellsocket, but guess what, I had to fix it every 
> time I mess around with the system even adding an extension, 
> it was soooo annoying, that now I have two systems running, 
> one with a at h and another
> plain *... ;)   Heck at least I learn to deal with both now.. 
> jejejejeje
> 
> Manny
> 
> -----Original Message-----
> From: asterisk-users-bounces at lists.digium.com
> [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of 
> Tom Rymes
> Sent: Friday, August 12, 2005 4:43 PM
> To: Asterisk Users Mailing List - Non-Commercial Discussion
> Subject: Re: [Asterisk-Users] TDM400P FXO channel hookstate 
> always "Offhook" &outbound digits sent before provider dialtone
> 
> Open the A at H AMP interface, click on trunks, and click on the entry  
> for your ZAP trunk. Then, put 'ww' in the "Outbound Dial Prefix"
> 
> Tom
> 
> On Aug 12, 2005, at 1:29 PM, Stephen Joyce wrote:
> 
> > I have an Asterisk at Home 1.3 server (Asterisk 1.0.9) and recently
> > TDM400P with (1) FXO card on port 4. Inbound calls are always  
> > but outbound calls fail 75% of the time with intercept messages  
> > dial tone provider that include "we're sorry, your call did not go
> > through", and "we're sorry, when placing a local call it is now
> > necessary to dial an area code and the 7-digit number".
> > I have connected a test set in monitor mode to the phone line to  
> > to what's being sent out the line by the Zap channel and 10 
> digits are
> > sent but the first digit is usually sent only as I hear the 
> dial tone
> > being drawn from the line, so it appears that it's sent before the
> > provider is ready to receive it. I can't find any sort of 
> setting that
> > would allow me to manually configure a dialing delay on the line,  
> > suspect this would provide a band-aid.
> > When looking at the Asterisk CLI, I see that the correct number is  
> > dialed by my dial plan. I am calling from SIP extension 1100 and  
> > 770-555-1234, which is a local 10-digit phone number.
> > -- Executing Dial("SIP/1100-9adc", "ZAP/g0/7705551234") in new stack
> > -- Called g0/7705551234
> > -- Zap/4-1 answered SIP/1100-9adc
> > The status of the channel is "Offhook" regardless of 
> whether or not  
> > phone line is actually Offhook or completely idle. I'm assuming that
> > when the line seems idle, it should show as Onhook.
> 
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com 
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>