[Asterisk-Users] TE11OP -> Mitel 200Sx??

Henry Devito hdevito at mchsi.com
Sat Apr 23 23:05:02 MST 2005 

I am trying to locate the manual for that level software.  If it's not here 
at home it is at my office and I will look everything up in the morning.
----- Original Message ----- 
From: "Scott Wolfe" <scottwolfe at orbus.net>
To: "Asterisk Users Mailing List - Non-Commercial Discussion" 
<asterisk-users at lists.digium.com>; <dwalker at jackson-tube.com>
Sent: Saturday, April 23, 2005 9:00 PM
Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??


> The Switch is since 1995 and I get a SX-200 Digital G1005 ENH 672P / F25.0 
> 09-FEB1994 when I look up the software on the switch board so if I am 
> reading what your telling me then I have to do D4/AMI. So does my zaptel 
> look correct? Maybe my cableing is off.
> Thanks,
>  -Scott
> ----- Original Message ----- 
> From: "Henry Devito" <hdevito at mchsi.com>
> To: <dwalker at jackson-tube.com>; "Asterisk Users Mailing List - 
> Non-Commercial Discussion" <asterisk-users at lists.digium.com>
> Sent: Friday, April 22, 2005 8:34 PM
> Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??
>
>
>> Of course there are exceptions to the rules.  I see now on a couple 
>> software releases where they do allow PRI with D4/AMI and PRI with 
>> esf/b8zs.  It's been a year or so since I messed with trunking on a 200, 
>> I've mostly been installing and maintaining the SX2000's and 3300's.
>>
>> Henry
>>
>>
>>
>> ----- Original Message ----- 
>> From: "Dennis Walker" <dwalker at jackson-tube.com>
>> To: "'Asterisk Users Mailing List - Non-Commercial Discussion'" 
>> <asterisk-users at lists.digium.com>
>> Sent: Friday, April 22, 2005 9:13 PM
>> Subject: RE: [Asterisk-Users] TE11OP -> Mitel 200Sx??
>>
>>
>>>I have done the same thing with an sx200 and a pri circuit
>>>
>>> My sx200 can only do ami d4 and e&m channels
>>>
>>> Here's parts of my config that takes the pri and converts it to e&m with
>>> ANI & DNIS
>>>
>>> zaptel.conf
>>>
>>> # t1 connected to the PRI circuit
>>> span=1,1,0,exf,b8zs
>>>
>>> # t1 connected to SX200
>>> # the t1 card on my sx200 did d4 ami and I supplied ANI and DNIS through
>>> the dial plan
>>>
>>> span=2,0,0,d4,ami
>>>
>>> bchan=1-23
>>> dchan=24
>>> e&m=25-47
>>> ---------------------------------------------
>>> zapata.conf
>>>
>>> [channels]
>>>
>>> echocancel=yes
>>> echocancelwhenbridged=yes
>>> echotraining=no
>>> rxgain=0.0
>>> txgain=0.0
>>> useincomingcalleridonzaptransfer=yes
>>> restrictcid=no
>>> context=default
>>> usecallingpres=yes
>>> usercallerid=yes
>>> hidecallerid=no
>>> callerid="Company Name"<8005551212>
>>> signalling=pri_cpe
>>> switchtype=dms100
>>> group=1
>>> channel => 1-23
>>>
>>> group=2
>>> signalling=em_w
>>> emdigitwait=500
>>> channel => 24-47
>>>
>>> # I needed the emdigitwait=500 to wait long enough for the SX200 to dial
>>> out it's digits
>>>
>>>
>>> --------------------------------------------------
>>> extensions.conf
>>>
>>> # our PRI circiut gave us the last 4 digits of the dialed number and 
>>> this
>>> is how I passed
>>> #   *ANI*DNIS*  to the SX200 for it to decode
>>>
>>> # the first group were individual numbers that mapped to faxes and 
>>> modems
>>>
>>> exten => 1234,1,Dial(Zap/g2/*${CALLERIDNUM}*${EXTEN}*,,r)
>>> exten => 5555,1,Dial(Zap/g2/*${CALLERIDNUM}*${EXTEN}*,,r)
>>> exten => 3333,1,Dial(Zap/g2/*${CALLERIDNUM}*${EXTEN}*,,r)
>>>
>>> # this set mapped our did 5000 - 5199 to the SX200
>>>
>>> exten => _5[0-1]XX,1,Dial(Zap/g2/*${CALLERIDNUM}*${EXTEN}*,,r)
>>>
>>> The reset of the dial plan took what ever I set up in the sx200 ARS to 
>>> dial
>>> out and
>>> sent out put Zap/G1
>>>
>>>
>>> Hope this helps
>>>
>>>
>>>
>>>
>>> ----------
>>> From: Henry Devito[SMTP:hdevito at mchsi.com]
>>> Reply To: Asterisk Users Mailing List - Non-Commercial Discussion
>>> Sent: Friday, April 22, 2005 8:56 PM
>>> To: Scott Wolfe; Asterisk Users Mailing List - Non-Commercial Discussion
>>> Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??
>>>
>>> <<File: ATT00262.html>><<File: ATT00263.txt>>
>>> I was wrong.  I just looked in my Mitel I&M's.  What level software are 
>>> you
>>> on in the SX200?  Up until a certain level 200's could only do D4/AMI 
>>> T1's,
>>> they could not do PRI's.  If it is a newer switch within the past 3 
>>> years
>>> or an older switch with later software than you can do PRI, but the
>>> signaling and framing must be ESF/B8ZS.
>>>
>>> Henry
>>>  ----- Original Message -----
>>>  From: Scott Wolfe
>>>  To: mike at shelcomm.com ; Asterisk Users Mailing List - Non-Commercial
>>> Discussion
>>>  Sent: Friday, April 22, 2005 7:04 PM
>>>  Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??
>>>
>>>
>>>
>>>
>>>  Thanks,
>>>    This is what I have now, but my Mitel PBX and Asterisk Box are unable
>>> to communicate via the T1 connection. Asterisk loads ok but I get error
>>> lights (blinking orange) on my TE110P and on my Mitel T1 card. Hummmm
>>>
>>>
>>>  -Scott
>>>
>>>  /etc/zaptel.conf
>>>  loadzone = us
>>>  defaultzone=us
>>>  span=1,0,0,d4,ami
>>>  bchan=1-23
>>>  dchan=24
>>>
>>>  /etc/asterisk/zapata.conf
>>>  [trunkgroups]
>>>
>>>  [channels]
>>>  context=default
>>>  switchtype=dms100
>>>  rxwink=300
>>>  usecallerid=no
>>>  hidecallerid=no
>>>  callwaiting=no
>>>  usecallingpres=yes
>>>  callwaitingcallerid=no
>>>  threewaycalling=yes
>>>  transfer=yes
>>>  canpark=yes
>>>  cancallforward=yes
>>>  callreturn=yes
>>>  echocancel=yes
>>>  echocancelwhenbridged=yes
>>>  rxgain=0.0 ;into the pstn twords the telco
>>>  txgain=0.0
>>>  callgroup=1
>>>  pickupgroup=1
>>>  immediate=yes
>>>
>>>  signalling=pri_cpe
>>>  group=1
>>>  context=default
>>>  emdigitwait=500
>>>  channel => 1-23 ; Set this to 1-15,17-31 for E1
>>>
>>>
>>>
>>>
>>>    ----- Original Message -----
>>>    From: Michael D Schelin
>>>    To: Asterisk Users Mailing List - Non-Commercial Discussion
>>>    Sent: Friday, April 22, 2005 4:48 PM
>>>    Subject: Re: [Asterisk-Users] TE11OP -> Mitel 200Sx??
>>>
>>>
>>>    Hello Henry
>>>    e&m=1-23 should be bchan=1-23
>>>    you have it set for analog
>>>    also
>>>    signaling=pri_cpe
>>>
>>>
>>>    Henry Devito wrote:
>>>
>>>      Don't you need one of these directives so the PRI knows which is
>>> master and which is slave?
>>>
>>>      a.. pri_cpe: PRI signaling, CPE side
>>>      a.. pri_net: PRI signaling, Network side
>>>
>>>      Henry
>>>        ----- Original Message -----
>>>        From: Scott Wolfe
>>>        To: Asterisk-Users at lists.digium.com
>>>        Sent: Friday, April 22, 2005 11:01 AM
>>>        Subject: [Asterisk-Users] TE11OP -> Mitel 200Sx??
>>>
>>>
>>>        Hello all. I just received a TE110P and am trying to hook it to 
>>> my
>>> Mitel 200SX has anyone successfully done this? My configuration is as
>>> follows.
>>>
>>>
>>>        Asterisk -> TE110P ->Kentrox (csu/dsu) -> Mitel T1 Card.
>>>
>>>
>>>        All I get is a blinking yellow on my TE110P card and an alarm on 
>>> my
>>> Mitel. T1 card.
>>>
>>>
>>>        Any advice would be great.
>>>
>>>
>>>        Zaptel.conf
>>>
>>>        span=1,0,1,d4,ami
>>>
>>>        e&m=1-23
>>>
>>>        dchan=24
>>>
>>>
>>>        Zapata.conf
>>>
>>>        signalling=em_w
>>>
>>>        switchtype=dms100
>>>
>>>        echocancel=yes
>>>
>>>        echocancelwhenbridged=yes
>>>
>>>        echotraining=400
>>>
>>>        callerid=asreceived
>>>
>>>        group=1
>>>
>>>        context=default
>>>
>>>        channel => 1-23
>>>
>>>
>>>
>>>
>>> ------------------------------------------------------------------------
>>>        _______________________________________________
>>>        Asterisk-Users mailing list
>>>        Asterisk-Users at lists.digium.com
>>>        http://lists.digium.com/mailman/listinfo/asterisk-users
>>>        To UNSUBSCRIBE or update options visit:
>>>           http://lists.digium.com/mailman/listinfo/asterisk-users
>>> --------------------------------------------------------------------------
>>> _______________________________________________
>>> Asterisk-Users mailing list
>>> Asterisk-Users at lists.digium.com
>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>> To UNSUBSCRIBE or update options visit:
>>>   http://lists.digium.com/mailman/listinfo/asterisk-users
>>>
>>>
>>>
>>> ------------------------------------------------------------------------
>>> ----
>>>
>>>
>>>    _______________________________________________
>>>    Asterisk-Users mailing list
>>>    Asterisk-Users at lists.digium.com
>>>    http://lists.digium.com/mailman/listinfo/asterisk-users
>>>    To UNSUBSCRIBE or update options visit:
>>>       http://lists.digium.com/mailman/listinfo/asterisk-users
>>>
>>>
>>> ------------------------------------------------------------------------
>>> ------
>>>
>>>
>>>  _______________________________________________
>>>  Asterisk-Users mailing list
>>>  Asterisk-Users at lists.digium.com
>>>  http://lists.digium.com/mailman/listinfo/asterisk-users
>>>  To UNSUBSCRIBE or update options visit:
>>>     http://lists.digium.com/mailman/listinfo/asterisk-users
>>>
>>> _______________________________________________
>>> Asterisk-Users mailing list
>>> Asterisk-Users at lists.digium.com
>>> http://lists.digium.com/mailman/listinfo/asterisk-users
>>> To UNSUBSCRIBE or update options visit:
>>>   http://lists.digium.com/mailman/listinfo/asterisk-users
>>
>> _______________________________________________
>> Asterisk-Users mailing list
>> Asterisk-Users at lists.digium.com
>> http://lists.digium.com/mailman/listinfo/asterisk-users
>> To UNSUBSCRIBE or update options visit:
>>   http://lists.digium.com/mailman/listinfo/asterisk-users
>
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users

More information about the asterisk-users mailing list