[Asterisk-Users] Cisco 7960G "disk full error"

[Brian West]

As of 7.x the UAL is what the phone loads..  Nothing to be CAREFUL of.

bkw

> -----Original Message-----
> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-
> bounces at lists.digium.com] On Behalf Of Shilliday, Jim
> Sent: Tuesday, October 12, 2004 5:32 PM
> To: Asterisk Users Mailing List - Non-Commercial Discussion
> Subject: RE: [Asterisk-Users] Cisco 7960G "disk full error"
> 
> Careful - in the later versions, P00* no longer specifies a protocol, it's
> actually the UAL.
> 
> 
> 
> Jim Shilliday
> 
> 
> 
> -----Original Message-----
> From: Andrew Edmond [mailto:edmond at candlepeople.com]
> Sent: Tuesday, October 12, 2004 5:59 PM
> To: 'Asterisk Users Mailing List - Non-Commercial Discussion'
> Subject: RE: [Asterisk-Users] Cisco 7960G "disk full error"
> 
> 
> 
> Henry,
> 
> 
> 
> Thanks!  This is a step in the right direction...
> 
> 
> 
> However, since it has P00* firmware on it, it never downloads
> SIPDefault.cnf.  I guess I'll have to make SEPDefault.cnf as small as
> possible then...?
> 
> 
> 
> Andrew
> 
> 
> 
> 	-----Original Message-----
> 	From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-
> users-bounces at lists.digium.com] On Behalf Of Henry Devito
> 	Sent: Tuesday, October 12, 2004 2:43 PM
> 	To: 'Asterisk Users Mailing List - Non-Commercial Discussion'
> 	Subject: RE: [Asterisk-Users] Cisco 7960G "disk full error"
> 
> 	The buffer is full on the 7960 because it keeps the old software
> along with downloading the new software just incase the new software
> fails.  What I have been doing is using a very generic SIPDefault.cnf and
> that allows enough space to download the upgrades.
> 
> 
> 
> 	This is the SIPDefault.cnf I use for upgrades.  Once the upgrade is
> done use your original SIPDefault.
> 
> 
> 
> 	image_version: "P0S3-04-4-00"
> 
> 	# Proxy Server
> 
> 	proxy1_address: "192.168.254.4"
> 
> 	proxy6_port:"5060"
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> ________________________________
> 
> 
> 	From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-
> users-bounces at lists.digium.com] On Behalf Of Andrew Edmond
> 	Sent: Tuesday, October 12, 2004 4:26 PM
> 	To: asterisk-users at lists.digium.com
> 	Subject: [Asterisk-Users] Cisco 7960G "disk full error"
> 
> 
> 
> 	Hello,
> 
> 
> 
> 	I'm trying to upgrade my 7960G that I bought off ebay to SIP 7.2
> firmware.  Apparently this phone had pretty old firmware on it... it's
> using Application Load ID P003H310 (version 3.0.12 Call Manager).
> 
> 
> 
> 	I've setup both a UNIX and Windows (SolarWinds) tftp server, and
> acquired firmware images for SIP 3.2, 4.4, 5.3, 6.3, and 7.2.
> 
> 
> 
> 	I set my OS79XX.txt contents to 8.3 filenames to download P0S3-03-2-
> 00.bin (renamed to 8.3 filename P0S30320.bin).
> 
> 
> 
> 	The tftp server successfully logs the connection from the phone,
> succesfully downloads OS79XX.txt, and then starts to download
> P0S30320.bin.  After 391168 bytes of download (the file is 409k), the
> phone dumps the transfer.
> 
> 
> 
> 	So I installed ethereal on my windows server.  It shows that at
> packet 769 the cisco phone reports "Disk Full".
> 
> 
> 
> 	I looked into this and came up with these previous posts:
> 
> 
> 
> 	http://www.loligo.com/asterisk/Cisco/79xx/upgrading.79xx.phones
> 
> 	http://lists.digium.com/pipermail/asterisk-users/2003-
> October/023021.html
> 
> 
> 
> 	However, since my phone firmware is so old I assume that I might
> need SIP 2.3 firmware to get this going.
> 
> 
> 
> 	In actuality, this is taking WAY more time than I had anticipated,
> so finally I'm reaching out to anyone who has had old firmware like mine
> (P003H310) and successfully upgraded it.
> 
> 
> 
> 	Thank you!
> 
> 
> 
> 	Andrew Edmond