AW: [Asterisk-Users] zaphfc problem

Sebastian Böhm seb at exse.net
Tue Nov 30 12:34:48 MST 2004


Hi,

I solved the Problem:

the context defined in zaptel.conf:

context = zapincoming

was not in extensions.conf, so nothing worked. ( I assumend this context 
is only necessary for calls from zaptel, not to it)

This may be a bug: in the verbose log I found nothing like "[chan_zap] 
Could not initialize ..., due to ....", this had helped alot and had 
saved alot of hours (-;

/sebastian

Pascal C. Kocher wrote:

>Hello
>
>Make sure you run ztcfg only once(!) per reboot. A second time seems to
>kill the zaphfc module (even if it doesn't state an error)
>
>Do you have any wcfx* cards running?
>
>Best regards,
>Pascal.
>
>  
>
>>-----Ursprüngliche Nachricht-----
>>Von: Sebastian Böhm [mailto:seb at exse.net] 
>>Gesendet: Dienstag, 30. November 2004 17:04
>>An: asterisk-users at lists.digium.com
>>Betreff: [Asterisk-Users] zaphfc problem
>>
>>Hi,
>>
>>I have a problem with zaphfc in NT mode.
>>
>>I installed the card, the software and made a isdn crossover 
>>cable (with 
>>two 100Ohm resistors).
>>
>>But if I pickup the phone, there is no dialtone. Also I can't 
>>ring the 
>>phone from xlite.
>>
>>if I load the zaphfc module with debug=1 I see a message when 
>>I pickup 
>>the phone.
>>------
>>zaphfc: card 0 RX 8 bytes [ 0xfc 0xff 0x3 0xf 0x2c 0x4d 0x1 0xff ...]
>>zaphfc: card 0 RX 2 bytes [ 0x60 0xe4 !]
>>------
>>But two seconds later I can read on my phone's display : 
>>"Line Failure".
>>
>>What could cause that ?
>>
>>I installed the latest bristuff  ( Asterisk 
>>1.0.2-BRIstuffed-0.2.0-RC2b ).
>>
>>
>>-------
>>/etc/zaptel.conf
>>-------
>>loadzone=nl
>>defaultzone=nl
>>
>>span=1,1,3,ccs,ami
>>bchan=1-2
>>dchan=3
>>--------
>>
>>I loaded the module with:
>>insmod ./zaphfc.ko modes=1
>>
>>--------
>>/etc/asterisk/zapata.conf
>>--------
>>[channels]
>>switchtype = euroisdn
>>;signalling = bri_net
>>signalling = bri_net_ptmp
>>pridialplan = local
>>prilocaldialplan = local
>>echocancel = yes
>>overlapdial = no
>>immediate = no
>>usecallerid = yes
>>group = 1
>>context = zapincoming
>>channel => 1-2
>>--------
>>
>>--------
>>extensions.conf
>>---------
>>[fromxlite]
>>exten => 6,1,Dial(Zap/g1/4758645,60,r)
>>---------
>>
>>
>>-----
>>load modules
>>-----
>>zaptel: no version for "struct_module" found: kernel tainted.
>>Zapata Telephony Interface Registered on major 196
>>zaphfc: CCD/Billion/Asuscom 2BD0 configured at mem 0xc49b9e00 fifo 
>>0xc2678000(0x2678000) IRQ 9 HZ 1000
>>zaphfc: Card 0 configured for NT mode
>>zaphfc: 1 hfc-pci card(s) in this box.
>>Registered tone zone 3 (Netherlands)
>>zaphfc: card 0 layer 1 state = G2
>>zaphfc: card 0 layer 1 state = G3
>>-------
>>
>>
>>
>>Thank you in advance !
>>
>>Sebastian
>>_______________________________________________
>>Asterisk-Users mailing list
>>Asterisk-Users at lists.digium.com
>>http://lists.digium.com/mailman/listinfo/asterisk-users
>>To UNSUBSCRIBE or update options visit:
>>   http://lists.digium.com/mailman/listinfo/asterisk-users
>>
>>
>>    
>>




More information about the asterisk-users mailing list