[Asterisk-Users] T100P HDLC configuration

[Vasyl Rublyov]

Thank you, Michael

I tried to switch to FR mode... but it did not help. I tied DLCI as 16 
and 99... the same result.

I attached one more full config from Netopia and from my Linux+Zaptel 
T100P systems.


DEVICE=hdlc0
# MODE=hdlc
# MODE=cisco
MODE=fr
NETMASK=255.255.255.252
GATEWAY=REMOTE_IPADDR

# FR
FR_LMI=ansi
FR_PVC=pvc0
FR_DLC=16
# FR_DLC=99

case "$1" in
        'start')
                echo "Loading T1/HDLC modules..."
                /sbin/modprobe zaptel
                /sbin/modprobe wct1xxp
                /sbin/modprobe hdlc
                /sbin/modprobe syncppp
                /sbin/ztcfg -vvv
                echo -n "Configuring HDLC interfaces, with mode \"${MODE}\""
                if [ "${MODE}" == "hdlc" -o "${MODE}" == "cisco" ]; then
                        echo "..."
                        /sbin/sethdlc ${DEVICE} ${MODE}
                        /sbin/ifconfig ${DEVICE} ${LOCAL_IPADDR} 
pointopoint ${REMOTE_IPADDR}
                        /sbin/route add -net ${NETWORK} netmask 
${NETMASK} ${DEVICE}
                        echo "Configuring default gateway..."
                        /sbin/route add default gw ${GATEWAY} metric 1 
${DEVICE}
                elif [ "${MODE}" == "fr" ]; then
                        echo ", LMI \"${FR_LMI}\"..."
                        /sbin/sethdlc ${DEVICE} ${MODE} lmi ${FR_LMI}
                        /sbin/sethdlc ${DEVICE} create ${FR_DLC}
                        /sbin/ifconfig ${DEVICE} up
                        echo "Configuring Frame-Relay PVC \"${FR_PVC}\"..."
                        /sbin/ifconfig ${FR_PVC} ${LOCAL_IPADDR} 
pointopoint ${REMOTE_IPADDR}
                        /sbin/route add -net ${NETWORK} netmask 
${NETMASK} ${FR_PVC}
                        echo "Configuring default gateway..."
                        /sbin/route add default gw ${GATEWAY} metric 1 
${FR_PVC}
                else   
                        echo ", unknown mode..."
                fi
        ;;
        'stop')
                echo "Unloading default gateway..."
                /sbin/route del default
                echo -n "Unloading HDLC configuration."
                if [ "${MODE}" == "hdlc" -o "${MODE}" == "cisco" ]; then
                        echo ", hdlc/cisco mode..."
                        /sbin/route del -net ${NETWORK} netmask 
${NETMASK} ${DEVICE}
                        /sbin/ifconfig ${DEVICE} down
                elif [ "${MODE}" == "fr" ]; then
                        echo ", frame-relay mode..."
                        /sbin/route del -net ${NETWORK} netmask 
${NETMASK} ${FR_PVC}
                        /sbin/ifconfig ${FR_PVC} down
                        /sbin/sethdlc ${DEVICE} delete
                        /sbin/ifconfig ${DEVICE} down
                else   
                        echo ", unknown mode..."
                fi
                echo "Unloading T1/HDLI modules..."
                rmmod wct1xxp zaptel hdlc syncppp
        ;;
        'restart')
                $0 stop
                sleep 1
                $0 start
        ;;
        *)     
                echo "usage $0 start|stop|restart"
esac



# $ show config
#      frame-relay lmi type ansi
#      frame-relay tim none
#      hardware acceleration enable yes
#      ip gateway REMOTE_IPADDR
#      ip route 0.0.0.0/0 REMOTE_IPADDR low
#      interface t1 1 buildout 0-0.6
#      interface t1 1 channels count 24 start 1 contiguous rate 64k
#      interface t1 1 clock source network
#      interface t1 1 diagnostic mode normal
#      interface t1 1 dle hdlc
#      interface t1 1 encoding b8zs
#      interface t1 1 framing esf
#      interface t1 1 operation mode hdlc
#      interface t1 1 priority-queuing enable yes
#      interface t1 1 pvc 1 yes
#      interface t1 1 pvc 1 enable yes
#      interface t1 1 pvc 1 tag "Circuit 1"
#      interface t1 1 pvc 1 vpi 0
#      interface t1 1 pvc 1 vci 35
#      interface t1 1 pvc 1 cp default
#      interface t1 1 pvc 1 voice no
#      interface t1 1 pvc 1 pcr 0
#      interface t1 1 prm-enable no
#      interface t1 1 rfc1973 enable no
#      interface t1 1 rfc1973 dlci 16
#      interface t1 1 rfc1973 lmi none
#      interface t1 1 cell-format scrambled
#      interface t1 1 unused cell-format idle
#      interface t1 1 ds0-autodetect no
#      cp 1 yes
#      cp 1 tag 36.HCGA.101976.VA
#      cp 1 enable yes
#      cp 1 dle hdlc
#      cp 1 ip enable yes
#      cp 1 ip address local LOCAL_IPADDR/30
#      cp 1 ip address remote REMOTE_IPADDR/30
#      cp 1 ip addressing numbered
#      cp 1 ip dhcp client mode standard
#      cp 1 ip mask local 255.255.255.252
#      cp 1 ip mask remote 255.255.255.252
#      cp 1 ip nat enable no
#      cp 1 ip nat map-list "Easy-PAT List"
#      cp 1 ip nat server-list Easy-Servers
#      cp 1 ip negotiate-lan no
#      cp 1 ip netbios proxy enable no
#      cp 1 ip rip receive both
#      cp 1 ip rip transmit no
#      cp 1 ip multicast-fwd yes
#      cp 1 interface-group primary
#      ;Netopia 4622
#      name ""
#      preferences changes immediate yes
#      preferences console default menu
#      preferences date format mm/dd/yy
#      preferences output format verbose
#      preferences output mask bits
#      preferences time format 24-hour
#
# 
=========================================================================================================================

**

-- 
Thanks and regards,
  Vasyl Rublyov


-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20040522/2f9455a1/attachment.htm