[Asterisk-Users] Trunk doesn't work Adit 600/T100P

[Adnan Shah]

Hi !
I am connecting to Adit 600 thru a T100P card
I have configured 1-16 FXS channels and 17-24 FXO.
Everything looks fine on Asterisk side I get a tone
on all FXS channels, but when I try to dialout thru
one of the FXO channels 17-24 it doesn't connect to
the POTS line and echoes back my voice.
I use fxsls and fxols for the T1 channels and ls on
Adit side. Whats wrong here ?

here is my Adit conf....


voip-pbx> print config

---------------------------------------------------------

-Cactus.lite configuration file

-Created on 01/01/1999 at 00:02:49 for adnan

-This file is valid for the following configuration only:

-

-        CardType

-       --------

-SLOT A    T1x2       Code Revision:  1.3.1

-SLOT 1    FXSx8

-SLOT 2    FXSx8

-SLOT 3    FXSx8

-SLOT 4    FXSx8

-SLOT 5    FXOx8

-SLOT 6    FXSx8

-

-Note:  Lines beginning with '-' will be ignored as comme

-by the CLI.  Before downloading, review the sections of

-configuration file delimited by these comments and delet

-the commands that are not needed (e.g. 'set ip address'

-and 'add user' are likely candidates for deletion).

-

-While downloading, a character and line delay of 5 ms is

-recommended.

---------------------------------------------------------

 

-Turning off verification messages.

 

set verification off

 

-Setting local off.

 

set local off

 

-Disconnecting all connections.

 

disconnect a

disconnect 1

disconnect 2

disconnect 3

disconnect 4

disconnect 5

disconnect 6

 

-Setting users.

 

add user adnan

 

-Setting network id.

 

set id "voip-pbx"

 

-Setting primary and secondary clock sources.

set clock1 a:1

set clock2 internal

 

-Setting IP addresses.

 

set ethernet ip address 192.168.7.151 255.255.255.192

set ip gateway 0.0.0.0

 

-Setting the SNMP MIB-II System Group objects.

 

set snmp getcom "public"

set snmp setcom "public"

set snmp trapcom "public"

 

-Setting slot a.

 

set a:1 up

set a:1 fdl none

set a:1 lbo 1

set a:1 framing esf

set a:1 id "CAC DS1# 01"

set a:1 linecode b8zs

set a:1 loopdetect on

set a:1 threshold min15 uas default

set a:1 threshold min15 ses default

set a:1 threshold min15 es default

set a:1 threshold min15 sefs default

set a:1 threshold min15 les default

set a:1 threshold min15 css default

set a:1 threshold min15 bes default

set a:1 threshold min15 dm default

set a:1 threshold min15 lcv default

set a:1 threshold min15 pcv default

set a:1 threshold day uas default

set a:1 threshold day ses default

set a:1 threshold day es default

set a:1 threshold day sefs default

set a:1 threshold day les default

set a:1 threshold day css default

set a:1 threshold day bes default

set a:1 threshold day dm default

set a:1 threshold day lcv default

set a:1 threshold day pcv default

set a:1:1-24 signal ls

set a:1:1-24 type voice

set a:2 down

set a:2 fdl none

set a:2 lbo 1

set a:2 framing esf

set a:2 id "CAC DS1# 02"

set a:2 linecode b8zs

set a:2 loopdetect on

set a:2 threshold min15 uas default

set a:2 threshold min15 ses default

set a:2 threshold min15 es default

set a:2 threshold min15 sefs default

set a:2 threshold min15 les default

set a:2 threshold min15 css default

set a:2 threshold min15 bes default

set a:2 threshold min15 dm default

set a:2 threshold min15 lcv default

set a:2 threshold min15 pcv default

set a:2 threshold day uas default

set a:2 threshold day ses default

set a:2 threshold day es default

set a:2 threshold day sefs default

set a:2 threshold day les default

set a:2 threshold day css default

set a:2 threshold day bes default

set a:2 threshold day dm default

set a:2 threshold day lcv default

set a:2 threshold day pcv default

set a:2:1-24 signal ls

set a:2:1-24 type voice

 

-Setting slot 1.

 

set 1:1-8 signal ls

set 1:1-8 txgain 0

set 1:1-8 rxgain 0

set 1:1-8 linelength short

 

-Setting slot 2.

 

set 2:1-8 signal ls

set 2:1-8 txgain -3

set 2:1-8 rxgain -6

set 2:1-8 linelength short

 

-Setting slot 3.

 

set 3:1-8 signal ls

set 3:1-8 txgain -3

set 3:1-8 rxgain -6

set 3:1-8 linelength short

 

-Setting slot 4.

 

set 4:1-8 signal ls

set 4:1-8 txgain -3

set 4:1-8 rxgain -6

set 4:1-8 linelength short

 

-Setting slot 5.

 

set 5:1-8 signal ls

set 5:1-8 txgain 0

set 5:1-8 rxgain 0

 

-Setting slot 6.

 

set 6:1-8 signal ls

set 6:1-8 txgain -3

set 6:1-8 rxgain -6

set 6:1-8 linelength short

 

-Making connections.

 

connect a:1:1-8 1:1-8

connect a:1:9-16 2:1-8

connect a:1:17-24 5:1-8

 

-Turning verification on.