[Asterisk-Users] false busy using sipura spa-3000 with asterisk on solaris

[Logan O'Sullivan Bruns]

Please ignore this message. It turned out my problem was that the
Sipura was falsely detecting the CPC signal. Since doubling the CPC
detection interval time the problem has gone away completely.

Thanks,
  logan

On Wed, Jul 28, 2004 at 06:57:01PM -0700, Logan O'Sullivan Bruns wrote:
> I'm new to asterisk and already a fan. Please forgive me if my
> questions are covered by some FAQ and thanks in advance for any
> pointers anyone can give me.
> 
> The basic problem that I'm having is that sometimes outgoing calls
> result in a busy signal when the outgoing line is free. I'm thinking
> that the channel is timing out or something but haven't figured out
> how to debug or gather additional detail yet. (I've only been using
> asterisk for a couple of days. So, again, please pardon me if these
> are stupid questions.)
> 
> My home configuration is as follows. I have asterisk 1.0RC1 running on
> a sparc (solaris 10). I have an Sipura SPA 3000 on the same
> network. It has an one SIP accessible FXS port (5060), one SIP
> accessible FXO port (5061) and ethernet port. I have my land line is
> attached to the FXO port. All my home phones are attached to the FXS
> port. I want to set it up to route long distance through some voip
> provider like vonage but right now I set up to route calls from the
> land line or internet to my home phones or asterisk hosted voice
> mail. Incoming calls work perfectly. Voice mail works perfectly (with
> the minor exception that volume on gsm attachments is lower than I'd
> like.) Outgoing calls works sometimes and other times it just goes
> straight to a busy signal.
> 
> Despite the fact that outgoing works some of the time I'm wondering if
> I have the configuration wrong. Here is the outbound fragment from
> extensions.conf.
> 
> [outbound]
> ; Press * to reach voice mail
> exten => *,1,VoiceMailMain(${PHONES1VM})
> exten => *,2,Hangup
> 
> ; local calls
> exten => _NXXXXXX,1,Playback(transfer)		; "Please hold while..." 
> exten => _NXXXXXX,2,Dial(SIP/${EXTEN:0}@phone.gedanken.org:5061,20)
> exten => _NXXXXXX,3,Congestion
> 
> ; long distance
> exten => _1NXXNXXXXXX,1,Playback(transfer)		; "Please hold while..." 
> exten => _1NXXNXXXXXX,2,Dial(SIP/${EXTEN:0}@phone.gedanken.org:5061},20)
> exten => _1NXXNXXXXXX,3,Congestion
> 
> I'm not sure if this relevant but I have wondered if the sip incoming
> configuration for the FXO port might be interfering or conflicting in
> some way. Probably not but here is the sip.conf fragment anyway.
> 
> [5785]
> type=friend
> context=inbound
> host=dynamic
> secret=secret
> defaultip=10.0.1.190
> port=5061
> nat=no
> 
> I haven't seen any errors of messages of note in the /var/log/asterisk
> logs. I'm not positive that asterisk is generating the busy signal. I
> think so but I guess it could be possible that the spa3000 is. I know
> the remote end isn't busy because I'm testing by calling my cell
> phone.
> 
> I know Solaris isn't a well tested platform and I did have to make
> some minor code changes to get to compile on my sun box. However, the
> fact that almost everything works so perfectly makes me think that it
> is a configuration problem not a porting problem. 
> 
> Again, any advice, things to try and such would be greatly
> appreciated.
> 
> Thanks,
>   logan
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users