[Asterisk-Users] Has anyone connected to 7960 with consolecablefor setup?

[Randy MacKay]

When I push the settings button, nothing happens.  I never get a chance to
put in the password.

I think the previous owner may have messed up a firmware upgrade.

-----Original Message-----
From: asterisk-users-bounces at lists.digium.com
[mailto:asterisk-users-bounces at lists.digium.com]On Behalf Of Sean Cook
Sent: Thursday, December 16, 2004 11:40 AM
To: 'Asterisk Users Mailing List - Non-Commercial Discussion'
Subject: RE: [Asterisk-Users] Has anyone connected to 7960 with
consolecablefor setup?


Why can't you use the settings button?  If
you know the password (or using the default
password) you should be able to unlock the
phone and do a hard reset...

Sean

> -----Original Message-----
> From:
asterisk-users-bounces at lists.digium.com
>
[mailto:asterisk-users-bounces at lists.digium.c
om] On Behalf Of
> Randy MacKay
> Sent: Thursday, December 16, 2004 1:35 PM
> To: asterisk-users at lists.digium.com
> Subject: [Asterisk-Users] Has anyone
connected to 7960 with
> console cablefor setup?
>
> I have a Cisco 7960 phone.  I cannot seem
to use the settings
> button to get into the phone to change the
TFTP server.  I've
> set up a DHCP Server, TFTP Server with the
same address, and
> the phone requests the address of 0.0.0.0,
the server offers
> the  address of 192.168.2.2, but the phone
seems not to take it.
>
> I have no action on the TFTP side.
>
> So, since I can't seem to server the phone
anything by TFTP,
> and I can't use the settings button, then I
thought I might
> make a console cable (see below).  I tried
to use
> hyperTerminal, but got no response from the
phone.
>
> Anyone have any ideas?
>
> Thanks,
>
> Randy
>
>
>
> I found a link to make a Cisco Console
Cable for RJ-45.
>
http://www.hardwarebook.net/cable/serial/cisc
oconsole9.html
>
>   				DB9F RJ45
> Receive Data 		2 	3
> Transmit Data 		3 	6
> Data Terminal Ready 	4 	7
> Ground 			5 	4
> Ground 			5 	5
> Data Set Ready 		6 	2
> Request to Send 		7 	8
> Clear to Send 		8 	1
>
>
>
> The Console Access Manual, give the
following cable information:
>
> Console Cable Requirements
> You use a serial cable with a connector to
connect a PC and a
> phone. The cable uses an RJ-11 connector
for the phone and an
> RJ-45 connector to an
> RJ-45-to-DB9 converter for the PC. Table
D-1 shows the pinout
> requirements for the console cable.
>
> Table D-1 Console Cable Pinouts
> RJ-11 Connector 	RJ-45 Connector
> Pin 2 ==========	Pin 6
> Pin 3 ==========	Pin 4
> Pin 4 ==========	Pin 3
>
> So, I thought I would go right from DB9F to
RJ-11
> DB9F		RJ-45		RJ-11
> Pin 2		Pin 3		Pin 4
> Pin 5		Pin 4		Pin 3
> Pin 3		Pin 6		Pin 2
> ---
> Outgoing mail is certified Virus Free.
> Checked by AVG anti-virus system
(http://www.grisoft.com).
> Version: 6.0.817 / Virus Database: 555 -
Release Date: 12/15/2004
>
>
_____________________________________________
__
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
>
http://lists.digium.com/mailman/listinfo/aste
risk-users
> To UNSUBSCRIBE or update options visit:
>
http://lists.digium.com/mailman/listinfo/aste
risk-users
>


_______________________________________________
Asterisk-Users mailing list
Asterisk-Users at lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users
---
Incoming mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.817 / Virus Database: 555 - Release Date: 12/15/2004

---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.817 / Virus Database: 555 - Release Date: 12/15/2004