[Asterisk-Users] Zaptel doesn't see remote hangup ? euro-isdn

[joachim]

I think the reason is because the telephony equipment of your telco is 
still analog.
(In belgium it was the same, until they started replacing all the old stuff 
with fancy digital things.).

At 17:30 29/08/2004, you wrote:
>Hi,
>  in Spain that process is correct. If you setup a communication between
>a caller and a called, if called phone hangs, in caller side hear a
>silence, but is a correct process. It's is due to in the called side you
>can hangup a phone and pickup other phone without lost communication.
>
>
>Regards,
>srsergio
>
>-----Mensaje original-----
>De: asterisk-users-admin at lists.digium.com
>[mailto:asterisk-users-admin at lists.digium.com] En nombre de Walter Klomp
>Enviado el: jueves, 29 de julio de 2004 16:44
>Para: asterisk-users at lists.digium.com
>Asunto: [Asterisk-Users] Zaptel doesn't see remote hangup ? euro-isdn
>
>
>Hi
>
>Just received my spanky new TE405P today to replace my Cisco gateway...
>
>After much fiddling (I forgot to switch it to E1) I got it to work and
>everything "seems" to work perfectly on our ISDN PRI.
>
>If I dial-in from the PSTN to a SIP phone, the call goes through and if
>I
>hangup either the SIP phone or the remote end, the call gets
>disconnected
>and destroyed
>
>However, if I dial-in from the SIP phone to my PSTN and then hang up my
>PSTN
>phone, the call does not get disconnected. My SIP phone goes quiet but
>doesn't disconnect. If I a few seconds later pick up the PSTN phone
>again,
>the connection is still there. Only if I hangup the SIP phone, the call
>gets
>destroyed. It seems that Zap doesn't see the remote hangup...
>
>Here is my Zaptel config and my Zapata config. I presume the extensions
>config etc are OK as my call-flow never changed and things were working
>fine
>with my AS5300.
>
>Am I missing something ?  How do I debug the Zap channels ?
>
>Cheers,
>Walter Klomp
>
>/etc/zaptel.conf
>span=1,1,0,ccs,hdb3,crc4 # This is the line in question...
>span=2,1,0,ccs,hdb3,crc4 # not used yet span=3,0,0,ccs,hdb3,crc4 # not
>used yet span=4,0,0,ccs,hdb3,crc4 # not used yet # Span 1 bchan=1-15
>dchan=16 bchan=17-31 # Span 2 bchan=32-46 dchan=47 bchan=48-62 # Span 3
>bchan=63-77 dchan=78 bchan=79-93 # Span 4 bchan=94-108 dchan=109
>bchan=110-124
>
>alaw=1-124
>
>loadzone=uk
>defaultzone=uk
>
>/etc/asterisk/zapata.conf
>[channels]
>context=default
>switchtype=euroisdn
>signalling=pri_cpe
>usecallerid=yes
>hidecallerid=no
>callwaiting=yes
>callwaitingcallerid=yes
>threewaycalling=yes
>transfer=yes
>cancallforward=yes
>echocancel=yes
>rxgain=0.0
>txgain=0.0
>immediate=no
>; Channels inherit configuration above them
>; Span 1
>group=1
>signalling=pri_cpe
>channel => 1-15
>channel => 17-31
>
>; Span 2
>group=2
>signalling=pri_cpe
>channel => 32-46
>channel => 48-62
>
>; Span 3
>group=3
>signalling=pri_cpe
>channel => 63-77
>channel => 79-93
>
>; Span 4
>group=4
>signalling=pri_cpe
>channel => 94-108
>channel => 110-124
>
>_______________________________________________
>Asterisk-Users mailing list
>Asterisk-Users at lists.digium.com
>http://lists.digium.com/mailman/listinfo/asterisk-users
>To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>
>_______________________________________________
>Asterisk-Users mailing list
>Asterisk-Users at lists.digium.com
>http://lists.digium.com/mailman/listinfo/asterisk-users
>To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users