[Asterisk-Users] RE: T100P/ TSU 600 installation problem

[Alex Lopez]

What cable are you using, The SU600 to Digium cards need a crossover
cable.

1 to 4
2 to 5
4 to 1
5 to 2

That would stop it from not working,

also make sure that you have a span definition on the zaptel.con file.



Message: 7
Date: Mon, 25 Aug 2003 12:52:12 -0700 (PDT)
From: jerk face <jerkface2098 at yahoo.com>
Subject: RE: [Asterisk-Users] T100P/ TSU 600 installation problem
To: asterisk-users at lists.digium.com
Reply-To: asterisk-users at lists.digium.com

Each port is set to the proper signalling type (FXO,
FXS).  I can't find any other options for the
individual ports.
As for the timing and configuration of NI, I have
tried 
NI:
Timing Mode as both DTE and NI (my only choices)

Where else should I be checking?
(Before this morning, I hadn't even seen a channel
bank before, so I'm a little lost at the moment).

Thanks for your time.

--- Wade Weppler <weppler at wwworks-inc.com> wrote:
> Have you configured the TSU600 properly?  You have
> to allocate each FXO/FXS
> channel to a timeslot before it will work.  This is
> not automatically done
> (like the Adtran Total Access series).
> 
> Mind you, you should still have a sync light on the
> T1 card...
> 
> -wade
> 
> > -----Original Message-----
> > From: asterisk-users-admin at lists.digium.com
> [mailto:asterisk-users-
> > admin at lists.digium.com] On Behalf Of jerk face
> > Sent: Monday, August 25, 2003 3:01 PM
> > To: asterisk-users at lists.digium.com
> > Subject: RE: [Asterisk-Users] T100P/ TSU 600
> installation problem
> > 
> > My zapata.conf is located in /etc/asterisk and my
> > zaptel.conf is located in the /etc directory.
> > 
> > --- "Adams, Gavin" <gadams at promisant.com> wrote:
> > > > -----Original Message-----
> > > > From: jerk face
> [mailto:jerkface2098 at yahoo.com]
> > >
> > >
> > > > I seem to be having a problem with the T100P
> card.
> > >  So
> > > > far I have done the following:
> > > >
> > > > vi zaptel.conf
> > > > fxoks=1-22
> > > > fxsks=23-24
> > > > ...
> > > >
> > > > vi zapata.conf
> > > > ...
> > > > signalling=fxo_ks
> > > > ...
> > > > channel => 1-22
> > > > ...
> > > > signalling=fxs_ks
> > > > ...
> > > > channel => 23-24
> > > >
> > > > I then run
> > > > modprobe zaptel
> > > > modprobe wct1xxp
> > > > ztcfg -vv
> > > >
> > > > There are no errors to report.  In
> /proc/zaptel/1
> > > all
> > > > of the configured channels are listed.
> > >
> > > Crazy question, is zaptel.conf is /etc or
> > > /etc/asterisk? If the latter,
> > > try:
> > >
> > > 	ztcfg -c /etc/asterisk/zaptel.conf -vvv
> > >
> > > --- Gavin
> > >
> > > _______________________________________________
> > > Asterisk-Users mailing list
> > > Asterisk-Users at lists.digium.com
> > >
> >
>
http://lists.digium.com/mailman/listinfo/asterisk-users
> > 
> > 
> > __________________________________
> > Do you Yahoo!?
> > Yahoo! SiteBuilder - Free, easy-to-use web site
> design software
> > http://sitebuilder.yahoo.com
> > _______________________________________________
> > Asterisk-Users mailing list
> > Asterisk-Users at lists.digium.com
> >
>
http://lists.digium.com/mailman/listinfo/asterisk-users
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
>
http://lists.digium.com/mailman/listinfo/asterisk-users


__________________________________
Do you Yahoo!?
Yahoo! SiteBuilder - Free, easy-to-use web site design software
http://sitebuilder.yahoo.com