[Asterisk-Users] T100P Incoming Calls Drop

[Matthew Farley]

Unfortunately (from this aspect of debugging) the line is not a PRI...
It is what the CO guys refer to as a "channelized T-1 line", with 24
channels available.

Thanks for all the support!

-Matthew Farley

On Tue, 2003-04-08 at 16:48, Martin Pycko wrote:
> Is it a PRI ?
> 
> If yes then send "pri intense debug span <span_no>" log to the group ...
> 
> regards
> Martin
> 
> On 8 Apr 2003, Matthew Farley wrote:
> 
> > Many thanks for the suggestions so far... Unfortunately, setting
> > callprogress=no and busydetect=no (and entirely rebooting the system)
> > has had no effect on the call-dropping problem.
> >
> > While talking to the Central Office guys, they inquired as to precisely
> > what sort of trunk group it is that they should be providing to my
> > asterisk machine... They mentioned a 'PBX' type of trunk group (which
> > sounds most likely and is how it is configured now in the CO). Also,
> > they mentioned the possibility of changing it to a '2-way' trunk group.
> > They can also provision 'incoming-only' and 'outgoing only' for me, but
> > these really don't sound like what I'm looking for. They also mentioned
> > that they were getting a 'stuck MF sender' when a call comes in through
> > my T-1 (from the PSTN), which evidently means that in some way my
> > asterisk machine is not responding properly to the incoming call (and
> > the CO may be dropping the call since it was never entirely set up). In
> > case it matters, the CO itself is a Siemens DCO.
> >
> > Does anyone have a similar setup (that works), and happen to know how
> > the channelized T-1 is provisioned from the CO? If so, such information
> > might be very helpful. Thanks again for all your valuable support.
> >
> > Thanks,
> > -Matthew Farley
> >
> >
> >
> > On Tue, 2003-04-08 at 14:05, Wade Weppler wrote:
> > > You might want to turn off callprogress as well (callprogress=no) as it was
> > > hanging up on me as well.
> > >
> > > -wade
> > >
> > > > -----Original Message-----
> > > > From: asterisk-users-admin at lists.digium.com [mailto:asterisk-users-
> > > > admin at lists.digium.com] On Behalf Of Matthew Farley
> > > > Sent: Tuesday, April 08, 2003 2:30 PM
> > > > To: asterisk-users at lists.digium.com
> > > > Subject: Re: [Asterisk-Users] T100P Incoming Calls Drop
> > > >
> > > > Unfortunately, setting busydetect=no had no effect on the issue. I
> > > > changed this in the config file and issued a reload command to the
> > > > asterisk console (I assume that this would be sufficient to implement
> > > > the change).
> > > >
> > > > Any other suggestions would be most welcome...
> > > >
> > > > Thanks!
> > > > -Matthew Farley
> > > >
> > > > On Tue, 2003-04-08 at 12:48, Martin Pycko wrote:
> > > > > add this to zapata.conf
> > > > >
> > > > > busydetect=no
> > > > >
> > > > > regards
> > > > > Martin
> > > > > On 8 Apr 2003, Matthew Farley wrote:
> >
> > _______________________________________________
> > Asterisk-Users mailing list
> > Asterisk-Users at lists.digium.com
> > http://lists.digium.com/mailman/listinfo/asterisk-users
> >
> 
> _______________________________________________
> Asterisk-Users mailing list
> Asterisk-Users at lists.digium.com
> http://lists.digium.com/mailman/listinfo/asterisk-users
-- 
Matthew Farley <asterisk at wheatstate.net>