<div dir="ltr">Hi,<br><br>I am having trouble with two issues here. <br>1. Is there any winpipe version that supports DAHDI?<br><br>2. <br><br>With zaptel installed, I can't get my channels configured:<br><br>root@localhost etc]# ztcfg -vv<br>
<br>Zaptel Version: <a href="http://1.4.12.1">1.4.12.1</a><br>Echo Canceller: MG2<br>Configuration<br>======================<br><br>SPAN 1: CCS/HDB3 Build-out: 0 db (CSU)/0-133 feet (DSX-1)<br><br>Channel map:<br><br>Channel 01: Clear channel (Default) (Slaves: 01)<br>
Channel 02: Clear channel (Default) (Slaves: 02)<br>Channel 03: Clear channel (Default) (Slaves: 03)<br>Channel 04: Clear channel (Default) (Slaves: 04)<br>Channel 05: Clear channel (Default) (Slaves: 05)<br>Channel 06: Clear channel (Default) (Slaves: 06)<br>
Channel 07: Clear channel (Default) (Slaves: 07)<br>Channel 08: Clear channel (Default) (Slaves: 08)<br>Channel 09: Clear channel (Default) (Slaves: 09)<br>Channel 10: Clear channel (Default) (Slaves: 10)<br>Channel 11: Clear channel (Default) (Slaves: 11)<br>
Channel 12: Clear channel (Default) (Slaves: 12)<br>Channel 13: Clear channel (Default) (Slaves: 13)<br>Channel 14: Clear channel (Default) (Slaves: 14)<br>Channel 15: Clear channel (Default) (Slaves: 15)<br>Channel 16: D-channel (Default) (Slaves: 16)<br>
Channel 17: Clear channel (Default) (Slaves: 17)<br>Channel 18: Clear channel (Default) (Slaves: 18)<br>Channel 19: Clear channel (Default) (Slaves: 19)<br>Channel 20: Clear channel (Default) (Slaves: 20)<br>Channel 21: Clear channel (Default) (Slaves: 21)<br>
Channel 22: Clear channel (Default) (Slaves: 22)<br>Channel 23: Clear channel (Default) (Slaves: 23)<br>Channel 24: Clear channel (Default) (Slaves: 24)<br>Channel 25: Clear channel (Default) (Slaves: 25)<br>Channel 26: Clear channel (Default) (Slaves: 26)<br>
Channel 27: Clear channel (Default) (Slaves: 27)<br>Channel 28: Clear channel (Default) (Slaves: 28)<br>Channel 29: Clear channel (Default) (Slaves: 29)<br>Channel 30: Clear channel (Default) (Slaves: 30)<br>Channel 31: Clear channel (Default) (Slaves: 31)<br>
<br style="color: rgb(204, 0, 0);"><span style="color: rgb(204, 0, 0);">31 channels to configure.</span><br><br><br>[root@localhost asterisk]# cat /proc/zaptel/1<br>Span 1: WPE1/0 "wanpipe1 card 0" (MASTER) HDB3/CCS/CRC4 RED<br>
<br> 1 WPE1/0/1 Clear RED<br> 2 WPE1/0/2 Clear RED<br> 3 WPE1/0/3 Clear RED<br> 4 WPE1/0/4 Clear RED<br> 5 WPE1/0/5 Clear RED<br> 6 WPE1/0/6 Clear RED<br> 7 WPE1/0/7 Clear RED<br>
8 WPE1/0/8 Clear RED<br> 9 WPE1/0/9 Clear RED<br> 10 WPE1/0/10 Clear RED<br> 11 WPE1/0/11 Clear RED<br> 12 WPE1/0/12 Clear RED<br> 13 WPE1/0/13 Clear RED<br> 14 WPE1/0/14 Clear RED<br>
15 WPE1/0/15 Clear RED<br> 16 WPE1/0/16 HDLCFCS RED<br> 17 WPE1/0/17 Clear RED<br> 18 WPE1/0/18 Clear RED<br> 19 WPE1/0/19 Clear RED<br> 20 WPE1/0/20 Clear RED<br> 21 WPE1/0/21 Clear RED<br>
22 WPE1/0/22 Clear RED<br> 23 WPE1/0/23 Clear RED<br> 24 WPE1/0/24 Clear RED<br> 25 WPE1/0/25 Clear RED<br> 26 WPE1/0/26 Clear RED<br> 27 WPE1/0/27 Clear RED<br> 28 WPE1/0/28 Clear RED<br>
29 WPE1/0/29 Clear RED<br> 30 WPE1/0/30 Clear RED<br> 31 WPE1/0/31 Clear RED<br><br><br>ifconfig:<br><br>w1g1 Link encap:Point-to-Point Protocol <br> UP POINTOPOINT NOARP MTU:8 Metric:1<br>
RX packets:0 errors:0 dropped:0 overruns:0 frame:0<br> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0<br> collisions:0 txqueuelen:100 <br> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)<br>
Interrupt:58 Memory:f8d30000-f8d31fff <br><br><br>[root@localhost asterisk]# wanrouter status<br><br>Devices currently active:<br> wanpipe1<br><br><br>Wanpipe Config:<br><br>Device name | Protocol Map | Adapter | IRQ | Slot/IO | If's | CLK | Baud rate |<br>
wanpipe1 | N/A | A101/1D/A102/2D/4/4D/8| 58 | 1 | 1 | N/A | 0 |<br><br>Wanrouter Status:<br><br>Device name | Protocol | Station | Status |<br>wanpipe1 | AFT TE1 | N/A | Connecting |<br>
<br><br><br>Any suggestion or hint will be greatly appreciated.<br><br>Thanks,<br>Mark<br><br></div>