[asterisk-ss7] LibSS7 and Sangoma A101 - SS7 HDLC Overrun Error
Gregory Massel
greg at csurf.co.za
Thu Oct 11 16:50:51 CDT 2012
This does not appear to be an SS7 issue.
Check your cables and connections, particularly for loose contacts or
potential shorts (e.g. where the jumper cable on the Krone block is
making poor contact or the cable hasn't been stripped cleanly and is
touching another pair or the frame itself, or where stranded cable has
been punched into a Krone block instead of solid core cable).
Sangoma cards can give signal strength readings. For info on how to get
this, check:
http://wiki.sangoma.com/Wanpipemon-T1-E1-physical-Line-alarms
It can also be load/interrupt related it you have multiple cards, but
unlikely with just one A101, unless an old motherboard and the card is
sharing IRQs unhappily with too many other devices.
See: http://wiki.sangoma.com/Wanpipe-Debugging
On 2012/10/11 10:28 PM, Geoffrey Yeoh wrote:
> Hi,
>
> I have a box with four A101 Sangoma E1 cards running Asterisk 1.8 with
> FreePBX. I've been getting this messages in CLI consistently
>
> [2012-10-11 20:33:55] NOTICE[11474]: chan_dahdi.c:3426
> my_handle_link_exception: SS7 got event: HDLC Abort(6) on span 1/0
> [2012-10-11 20:33:55] NOTICE[11474]: chan_dahdi.c:3426
> my_handle_link_exception: SS7 got event: HDLC Overrun(7) on span 1/0
> [2012-10-11 20:33:57] NOTICE[11474]: chan_dahdi.c:3426
> my_handle_link_exception: SS7 got event: HDLC Abort(6) on span 1/0
> [2012-10-11 20:34:30] NOTICE[11474]: chan_dahdi.c:3426
> my_handle_link_exception: SS7 got event: HDLC Abort(6) on span 1/0
> [2012-10-11 20:34:31] NOTICE[11474]: chan_dahdi.c:3426
> my_handle_link_exception: SS7 got event: HDLC Overrun(7) on span 1/0
> [2012-10-11 20:34:33] NOTICE[11474]: chan_dahdi.c:3426
> my_handle_link_exception: SS7 got event: HDLC Bad FCS(8) on span 1/0
> [2012-10-11 20:35:06] NOTICE[11474]: chan_dahdi.c:3426
> my_handle_link_exception: SS7 got event: HDLC Abort(6) on span 1/0
>
>
> My wanpipe configuration is as follows:
>
> [wanpipe1]
> CARD_TYPE = AFT
> S514CPU = A
> CommPort = PRI
> AUTO_PCISLOT = NO
> PCISLOT = 4
> PCIBUS = 2
> FE_MEDIA = E1
> FE_LCODE = HDB3
> FE_FRAME = NCRC4
> FE_LINE = 1
> TE_CLOCK = NORMAL
> TE_REF_CLOCK = 0
> TE_SIG_MODE = CCS
> TE_HIGHIMPEDANCE = NO
> TE_RX_SLEVEL = 430
> HW_RJ45_PORT_MAP = DEFAULT
> LBO = 120OH
> FE_TXTRISTATE = NO
> MTU = 1500
> UDPPORT = 9000
> TTL = 255
> IGNORE_FRONT_END = NO
> TDMV_SPAN = 1
> TDMV_DCHAN = 0
> TE_AIS_MAINTENANCE = NO #NO: defualt YES: Start port in AIS Blue
> Alarm and keep line down
> #wanpipemon -i w1g1 -c Ttx_ais_off to
> disable AIS maintenance mode
> #wanpipemon
> -i w1g1 -c Ttx_ais_on to enable AIS maintenance mode
> TDMV_HW_DTMF = YES # YES: receive dtmf events from
> hardware
> TDMV_HW_FAX_DETECT = YES # YES: receive fax 1100hz events
> from hardware
> HWEC_OPERATION_MODE = OCT_NORMAL # OCT_NORMAL: echo cancelation
> enabled with nlp (default)
>
> # OCT_SPEECH: improves software tone detection by disabling NLP (echo
> possible)
>
> # OCT_NO_ECHO:disables echo cancelation but allows VQE/tone functions.
> HWEC_DTMF_REMOVAL = NO # NO: default YES: remove dtmf out of
> incoming media (must have hwdtmf enabled)
> HWEC_NOISE_REDUCTION = NO # NO: default YES: reduces noise on the
> line - could break fax
> HWEC_ACUSTIC_ECHO = NO # NO: default YES: enables acustic echo
> cancelation
> HWEC_NLP_DISABLE = NO # NO: default YES: guarantees software tone
> detection (possible echo)
> HWEC_TX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio level
> to be maintained (-20 default)
> HWEC_RX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio level
> to be maintained (-20 default)
> HWEC_TX_GAIN = 0 # 0: disable -24-24: db values to
> be applied to tx signal
> HWEC_RX_GAIN = 0 # 0: disable -24-24: db values to
> be applied to tx signal
> [w1g1]
> ACTIVE_CH = ALL
> TDMV_HWEC = NO
> MTU = 8
>
> My chan_dahdi.conf is as follows:
>
> signaling=ss7 ;this is ss7 signaling
> ss7type=itu ;using the ITU variant
> ss7_called_nai=dynamic ;NAI for outgoing calls
> ss7_calling_nai=dynamic ;NAI for incoming calls
> ss7_internationalprefix=00 ;international prefix value for incoming calls
> ss7_nationalprefix=33 ;national prefix value for incoming calls
> ss7_subscriberprefix=3364 ;subscriber prefix value for incoming calls
> ss7_unknownprefix= ;unknown prefix value for incoming calls
> ;ss7_explictacm=yes ;ACM is send as soon as call enters the dial plan...may
> not accepted yet though
> ss7_autoacm=yes
>
> linkset=1 ;arbitrary name for this set of channels
> pointcode=6021 ;the point code for this system...aka SPC
> adjpointcode=6000 ;the point code for the system that we are signaling to...
> aka APC
> defaultdpc=6000 ;the point code for the system that the CICs will be
> negotiated with...aka DPC
> networkindicator=national ;NI value for MTP3
>
> cicbeginswith=1 ;the starting value of the CICs
> channel=1-15 ;the channels that are CICs
> cicbeginswith=17 ;the starting value of the CICs
> channel=17-31 ;the channels that are CICs
> sigchan=16
>
> cicbeginswith=32 ;the starting value of the CICs
> channel=32-46 ;the channels that are CICs
> cicbeginswith=48 ;the starting value of the CICs
> channel=48-62 ;the channels that are CICs
> sigchan=47
>
> cicbeginswith=63 ;the starting value of the CICs
> channel=63-77 ;the channels that are CICs
> cicbeginswith=79 ;the starting value of the CICs
> channel=79-93 ;the channels that are CICs
> sigchan=78
>
> cicbeginswith=94 ;the starting value of the CICs
> channel=94-108 ;the channels that are CICs
> cicbeginswith=110 ;the starting value of the CICs
> channel=110-124 ;the channels that are CICs
> sigchan=109
>
> and the system.conf:
>
> loadzone=us
> defaultzone=us
>
> #Sangoma A101 port 1 [slot:4 bus:2 span:1] <wanpipe1>
> span=1,1,0,ccs,hdb3
> bchan=1-15,17-31
> echocanceller=mg2,1-15,17-31
> mtp2=16
>
> #Sangoma A101 port 1 [slot:9 bus:2 span:2] <wanpipe2>
> span=2,2,0,ccs,hdb3
> bchan=32-46,48-62
> echocanceller=mg2,32-46,48-62
> mtp2=47
>
> #Sangoma A101 port 1 [slot:10 bus:2 span:3] <wanpipe3>
> span=3,3,0,ccs,hdb3
> bchan=63-77,79-93
> echocanceller=mg2,63-77,79-93
> mtp2=78
>
> #Sangoma A101 port 1 [slot:11 bus:2 span:4] <wanpipe4>
> span=4,4,0,ccs,hdb3
> bchan=94-108,110-124
> echocanceller=mg2,94-108,110-124
> mtp2=109
>
> I've used the above configuration countless times with problems - I am
> stumped.
>
> Any help and suggestions appreciated and welcome.
>
>
>
> Best regards,
> Geoffrey
>
>
>
>
>
>
> --
> _____________________________________________________________________
> -- Bandwidth and Colocation Provided by http://www.api-digital.com --
>
> asterisk-ss7 mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-ss7
More information about the asterisk-ss7
mailing list