[asterisk-ss7] Call conected but not ringing

her Garcia herlit11 at lycos.com
Sun Apr 22 07:17:53 CDT 2012


Hi, thanks for your replies. I ´ll try your suggestions. The reason I have differents adjpointcode and defaultdpc is that 
my carrier has a config of non associated ss7, which means that signalling goes exclusively to one node/switch and
the voice is carried to a different node/switch.

I was wondering if I should set up two different channels in my chan_dahdi.conf for each carrier´s switch?

[channels]
#First channel signalling only
language=en
...
sigchan=16
adjpointcode = 8122-> signalling node
defaultdpc = 8122  -> signalling node

#Second channel voice only
language=en
...
adjpointcode = 8845 -> voice node
defaultdpc = 8845  -> voice node
channel= 1-15
channel= 17-31


Have you seen this carrier setting before?

Thanks,regards
Hernán
Apr 22, 2012 07:59:02 AM, asterisk-ss7 at lists.digium.com wrote:

===========================================


Try putting sane point code in the adpointcode as defaultdpc
On Apr 20, 2012 7:16 PM, "her Garcia"  wrote:
Hi, everyone. I am working on asterisk+ss7.
When I try to make a call, the call connects but I have no audio or see no progress in the debug.


     -- Executing [111536972876 at incoming:2] Dial("SIP/1153640000-00000005", "DAHDI/17") in new stack
    -- Executing [111536972876 at incoming:2] Dial("SIP/1153640000-00000005", "DAHDI/17") in new stack
host*CLI>     -- Called DAHDI/17
    -- Called DAHDI/17

Nothing else. I believe it should also include the following:

>>     -- DAHDI/1-1 is proceeding passing it to SIP/600-08887770 ---  I don´t get this
>>     -- DAHDI/1-1 is ringing
>>     -- DAHDI/1-1 answered SIP/600-08887770

My linkset is up, my channels are ok. My carrier tells me that he doesn´t see any calls reaching his node.
I believe it´s because the call doesn´t progress. This is my config


The carrier says that his ss7 is semi-associated. Divides signalling in one node and voice trunks/circuits in
a second node. I only have the following to configure

adjpointcode=8122
defaultdpc=8845

I know defaultdpc is the remote end. Signalling is ok verified by my carrier, so I think my adjpointcode is ok.
The thing is that I also get messages from a third node in my debug, number "8923" saying the following:


 WARNING[18934]: sig_ss7.c:392 ss7_find_cic_gripe: Linkset 1: SS7 RLC requested unconfigured CIC/DPC 14/8923.

I understand its about the circuits. I tried configuring that node as my adjpointcode, but I can´t get through, it
maybe something on the Carrier side for this particular node(8923)

I have been working this for a couple of weeks, any ideas?
Thanks, I apologize for this long post.
Hernán

--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --

asterisk-ss7 mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-ss7

--
_____________________________________________________________________
-- Bandwidth and Colocation Provided by http://www.api-digital.com --

asterisk-ss7 mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-ss7



More information about the asterisk-ss7 mailing list