[asterisk-ss7] often receives BAD FCS errors
黄东涛
tprax634 at hotmail.com
Wed Apr 20 21:05:37 CDT 2011
Hi,
Amazing,it works. Thx a lot. But why does it always appears FCS errors when TE_CLOCK value is MASTER?
> Date: Wed, 20 Apr 2011 17:13:02 +0200
> From: tsearle at gmail.com
> To: asterisk-ss7 at lists.digium.com
> Subject: Re: [asterisk-ss7] often receives BAD FCS errors
>
> try changing
>
> TE_CLOCK to slave
>
> Torrey
>
> 2011/4/20 黄东涛 <tprax634 at hotmail.com>:
> > Hi,
> >
> > Anybody knows why my mtp2 link works fine but continuously appears BAD FCS
> > errors? What causes this error?
> >
> >
> > Here is my conf:
> > 1.dahdi/system.conf
> >
> > loadzone=us
> > defaultzone=us
> >
> > #Sangoma A102 port 1 [slot:4 bus:4 span:1] <wanpipe1>
> > span=1,1,0,ccs,hdb3,crc4
> > bchan=1-15,17-31
> > mtp2=16
> >
> > #Sangoma A102 port 2 [slot:4 bus:4 span:2] <wanpipe2>
> > span=2,2,0,ccs,hdb3,crc4
> > bchan=32-46,48-62
> > mtp2=47
> >
> > 2.wanpipe/wanpipe1.conf
> >
> > [devices]
> > wanpipe1 = WAN_AFT_TE1, Comment
> >
> > [interfaces]
> > w1g1 = wanpipe1, , TDM_VOICE, Comment
> >
> > [wanpipe1]
> > CARD_TYPE = AFT
> > S514CPU = A
> > CommPort = PRI
> > AUTO_PCISLOT = NO
> > PCISLOT = 4
> > PCIBUS = 4
> > FE_MEDIA = E1
> > FE_LCODE = HDB3
> > FE_FRAME = CRC4
> > FE_LINE = 1
> > TE_CLOCK = MASTER
> > TE_REF_CLOCK = 0
> > TE_SIG_MODE = CCS
> > TE_HIGHIMPEDANCE = NO
> > TE_RX_SLEVEL = 430
> > LBO = 120OH
> > FE_TXTRISTATE = NO
> > MTU = 1500
> > UDPPORT = 9000
> > TTL = 255
> > IGNORE_FRONT_END = NO
> > TDMV_SPAN = 1
> > TDMV_DCHAN = 0
> > TE_AIS_MAINTENANCE = NO #NO: defualt YES: Start port in AIS Blue
> > Alarm and keep line down
> > #wanpipemon -i w1g1 -c Ttx_ais_off to
> > disable AIS maintenance mode
> > #wanpipemon
> > -i w1g1 -c Ttx_ais_on to enable AIS maintenance mode
> > TDMV_HW_DTMF = NO # YES: receive dtmf events from
> > hardware
> > TDMV_HW_FAX_DETECT = NO # YES: receive fax 1100hz
> > events from hardware
> > HWEC_OPERATION_MODE = OCT_NORMAL # OCT_NORMAL: echo cancelation
> > enabled with nlp (default)
> >
> > # OCT_SPEECH: improves software tone detection by disabling NLP (echo
> > possible)
> >
> > # OCT_NO_ECHO:disables echo cancelation but allows VQE/tone functions.
> > HWEC_DTMF_REMOVAL = NO # NO: default YES: remove dtmf out of
> > incoming media (must have hwdtmf enabled)
> > HWEC_NOISE_REDUCTION = NO # NO: default YES: reduces noise on the
> > line - could break fax
> > HWEC_ACUSTIC_ECHO = NO # NO: default YES: enables acustic echo
> > cancelation
> > HWEC_NLP_DISABLE = NO # NO: default YES: guarantees software tone
> > detection (possible echo)
> > HWEC_TX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio level
> > to be maintained (-20 default)
> > HWEC_RX_AUTO_GAIN = 0 # 0: disable -40-0: default tx audio level
> > to be maintained (-20 default)
> > HWEC_TX_GAIN = 0 # 0: disable -24-24: db values to
> > be applied to tx signal
> > HWEC_RX_GAIN = 0 # 0: disable -24-24: db values to
> > be applied to tx signal
> >
> > [w1g1]
> > ACTIVE_CH = ALL
> > TDMV_HWEC = NO
> > MTU = 8
> >
> >
> > --
> > _____________________________________________________________________
> > -- Bandwidth and Colocation Provided by http://www.api-digital.com --
> >
> > asterisk-ss7 mailing list
> > To UNSUBSCRIBE or update options visit:
> > http://lists.digium.com/mailman/listinfo/asterisk-ss7
> >
>
> --
> _____________________________________________________________________
> -- Bandwidth and Colocation Provided by http://www.api-digital.com --
>
> asterisk-ss7 mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-ss7
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.digium.com/pipermail/asterisk-ss7/attachments/20110421/712555e9/attachment.htm>
More information about the asterisk-ss7
mailing list