[asterisk-ss7] chan_ss7 signalling across multiple servers

[Anders Baekgaard]

The config spec looks correct.

You will not need a [cluster] section when you use mtp3d to transport 
signaling for multiple servers.

You can also configure a cluster using the [cluster] section, and then not use 
mtp3d. There is a template ss7.conf for that in the source distribution.

The method of configuring clusters using the [cluster] section is the old 
approach. The newer approach of using mtp3d was introduced as a step towards 
supporting SIGTRAN, and for support of sharing transport for other protocols 
like GSM MAP and INAP.

Best regards,
-- 
Anders Baekgaard
Managing Director, Dicea ApS
Esromgade 15, 1110
DK-2200 Copenhagen N
Denmark
Tel: +45 46931411
Fax: +45 46931466
Mobile: +45 20771844

On Thursday 02 April 2009 14:03:00 Antoine Megalla wrote:
> Hi,
>
> So I wrote 1 ss7.conf for both servers as suggested, I just need comments
> if the file looks correct, or if it missing anything: Do I need a [cluster]
> section in the file:
>
> Here is my ss7.conf file:
>
> [linkset-MSC1]
> enabled => yes
> enable_st => no
> use_connect => yes
> hunting_policy => seq_htl
> subservice => auto
> context => ss7
> language => en
> t35 => 15000,timeout
>
> [link-l1]
> linkset => MSC1
> channels => 1-15,17-31
> schannel => 16,host1:12000
> firstcic => 1
> echocancel => no
> echocan_train => 350
> echocan_taps => 128
> enabled => yes
>
> [link-l2]
> linkset => MSC1
> channels => 1-31
> schannel =>
> firstcic => 33
> echocancel=allways
> echocan_taps=32
> echocan_train=350
> enabled => yes
>
> [link-l3]
> linkset => MSC1
> channels => 1-31
> schannel =>
> firstcic => 65
> echocancel=no
> echocan_taps=32
> echocan_train=350
> enabled => yes
>
> [link-l4]
> linkset => MSC1
> channels => 1-31
> schannel =>
> firstcic => 97
> echocancel=no
> echocan_taps=32
> echocan_train=350
> enabled => yes
>
> [link-l5]
> linkset => MSC1
> channels => 1-31
> schannel =>
> firstcic => 129
> echocancel=no
> echocan_taps=32
> echocan_train=350
> enabled => yes
>
> [link-l6]
> linkset => MSC1
> channels => 1-31
> schannel =>
> firstcic => 161
> echocancel=no
> echocan_taps=32
> echocan_train=350
> enabled => yes
>
> [link-l7]
> linkset => MSC1
> channels => 1-31
> schannel =>
> firstcic => 193
> echocancel=no
> echocan_taps=32
> echocan_train=350
> enabled => yes
>
> [link-l8]
> linkset => MSC1
> channels => 1-31
> schannel =>
> firstcic => 225
> echocancel=no
> echocan_taps=32
> echocan_train=350
> enabled => yes
>
> [host-host1]
> enabled => yes
> default_linkset => MSC1
> opc => 1000
> dpc => MSC1:2000
> links => l1:1,l2:2,l3:3,l4:4
> if-1 => 10.0.0.1
>
> [host-host2]
> enabled => yes
> default_linkset => MSC1
> opc => 1000
> dpc => MSC1:2000
> links => l5:1,l6:2,l7:3,l8:4
> if-1 => 10.0.0.2
>
>
> Appreciate your comments,
>
> Regards,
>
> Antoine Megalla.
>
>  
>
>
> ----- Original Message ----
> From: Anders Baekgaard <ab at dicea.dk>
> To: asterisk-ss7 at lists.digium.com
> Sent: Thursday, April 2, 2009 12:03:57 PM
> Subject: Re: [asterisk-ss7] chan_ss7 signalling across multiple servers
>
> Assuming link 'l1' has signaling on ts 16, and this is connected on server
> 'host1', you will write
>
> [link-l1]
> ...
> schannel => 16, host1:12000
> ...
>
>
> You must specify this on both servers. It is easiest to have the same
> configuration specification (ss7.conf) on both servers. chan_ss7 will
> forward signaling using TCP/IP to 'host1', port 12000, so you must ensure
> mtp3d is running on that server.
>
> Best regards,