[asterisk-ss7] Unable to match extension, context: ss7, dni: 6789, rni: (Using ISUP/Chan_ss7)
Yahya
medevelopers at gmail.com
Fri Nov 21 01:39:25 CST 2008
Dears
Thank you very much Anders for your prompt response I have tried the
suggested on and got the following output below but the problem is still the
same. See below the CLI out put and configuration for your reference.
One thing that I would like to ask you, is their any mean where I can get
the value of DNI? Or anything where I can store the value of DNI?
As far as I know we got the value on DNID in PRI where we can distinguish
between the calls but in ISUP the information I can see on CLI is DNI value.
See below the suggested with respective CLI output.
When I defined an extension for the dialing code 6789 in SS7 context. It
gave the below output on CLI
ss7.conf File content
----------------------------------------
[linkset-work1]
enabled => yes
enable_st => no
use_connect => yes
hunting_policy => odd_lru
context => ss7
language => en
t35 => 15000,timeout
subservice => auto
[link-l1]
linkset => work1
channels => 1-15,17-31
schannel => 16
firstcic => 1
enabled => yes
echocancel => no
echocan_train => 350
echocan_taps => 128
[host-work1.myplace.net]
enabled => yes
opc => 1234
dpc => work1:4567
links => l1:1
extentions.conf
------------------------------------------------
[general]
static=yes
writeprotect=no
[globals]
VOICE_TYPE=voice_kal_diphone
[ss7]
exten => 6789,1,Goto(my-extension,s,1)
exten => hang,1,Hangup
------------------------------------------------
Error Shown
[Nov 20 23:52:28] DEBUG[26580]: l4isup.c:1522 check_iam_sam: Setting
iam.dni.complete
== Starting **Unknown** at default,s,1 failed so falling back to exten 's'
== Starting **Unknown** at default,s,1 still failed so falling back to
context 'default'
[Nov 20 23:52:28] WARNING[26701]: pbx.c:2405 __ast_pbx_run: Channel
'**Unknown**' sent into invalid extension 's' in context 'default', but no
invalid
handler
[Nov 20 23:52:28] DEBUG[26701]: pbx.c:1621
pbx_substitute_variables_helper_full: Function result is '77142034884'
[Nov 20 23:52:28] DEBUG[26701]: pbx.c:1621
pbx_substitute_variables_helper_full: Function result is 's'
[Nov 20 23:52:28] DEBUG[26701]: pbx.c:1621
pbx_substitute_variables_helper_full: Function result is 'default'
[Nov 20 23:52:28] DEBUG[26701]: pbx.c:1621
pbx_substitute_variables_helper_full: Function result is '**Unknown**'
-- SS7 hangup '**Unknown**' CIC=7 Cause=0 (state=1)
[Nov 20 23:52:28] DEBUG[26701]: l4isup.c:1916 ss7_hangup: SS7 hangup
'**Unknown**' CIC=7 (state=1), chan=0x083e9500
[Nov 20 23:52:28] DEBUG[26701]: l4isup.c:1947 ss7_hangup: SS7 hangup
'**Unknown**' CIC=7 cause=0
[Nov 20 23:52:28] DEBUG[26701]: l4isup.c:389 mtp_enqueue_isup_packet: Queue
packet CIC=7, len=13, linkset='work1', link='l1', slinkset='work1',
slink='l1'
BR,
Yahya
On 11/20/08, Anders Baekgaard <ab at dicea.dk> wrote:
>
> chan_ss7 uses the dial plan to decide if an incoming call number is
> complete,
> or if it has to wait for further address messages (SAM) before accepting
> the
> call.
>
> In your setup, chan_ss7 tries to match the incoming call number (dni)
> against
> the dial plan in context "ss7" (you have specified context=ss7 in
> ss7.conf).
> But the dial plan context "ss7" is empty in your extensions.conf. I suggest
> you put the dial plan logic in that context, or change the ss7.conf to have
> context = default.
>
> Best regards,
> --
> Anders Baekgaard
> Managing Director, Dicea ApS
> Esromgade 15, 1110
> DK-2200 Copenhagen N
> Denmark
> Tel: +45 46931411
> Fax: +45 46931466
> Mobile: +45 20771844
>
> On Thursday 20 November 2008 09:56:21 Yahya wrote:
> > Dear
> > mates,
> >
> > I need your support in the below mentioned problem that I experienced and
> > still not resolved in ISUP connectivity with ZONG. Please advice if you
> > have any
> >
> > remedy or clue.
> >
> > I have successfully established SS7 links with the Telco and they are
> > working fine. I have tested an outgoing call and an incoming call as
> well.
> > The problem
> >
> > arises when I tried to define extension in it.
> >
> > At first I just add one dialing code as 6789 and successfully received a
> > call over it on default extension. When I add another dialing code and
> > define
> >
> > extension for it gave an error as
> >
> >
> > Error Shown
> >
> > [Nov 19 16:15:07] DEBUG[26580]: l4isup.c:2466 process_circuit_message:
> > Process circuit message IAM, CIC=6, state=0, reset_done=1
> > -- Recv IAM CIC=6 ANI=77142034884 DNI=6789 RNI= redirect=no/0
> > complete=1
> > [Nov 19 16:15:07] DEBUG[26580]: l4isup.c:2644 process_iam: IAM CIC=6,
> > owner=0x00000000
> > [Nov 19 16:15:07] DEBUG[26580]: l4isup.c:1530 check_iam_sam: Unable to
> > match extension, context: ss7, dni: 6789, rni:
> > [Nov 19 16:15:07] DEBUG[26580]: l4isup.c:389 mtp_enqueue_isup_packet:
> Queue
> > packet CIC=6, len=13, linkset='work1', link='l3', slinkset='work1',
> > slink='l1'
> >
> > ss7.conf File content
> > ----------------------------------------
> > [linkset-work1]
> > enabled => yes
> > enable_st => no
> > use_connect => yes
> > hunting_policy => odd_lru
> > context => ss7
> > language => en
> > t35 => 15000,timeout
> > subservice => auto
> >
> > [link-l1]
> > linkset => work1
> > channels => 1-15,17-31
> > schannel => 16
> > firstcic => 1
> > enabled => yes
> > echocancel => no
> > echocan_train => 350
> > echocan_taps => 128
> >
> > [host-work1.myplace.net]
> > enabled => yes
> > opc => 1234
> > dpc => work1:4567
> > links => l1:1
> >
> >
> > When I first tried to test my connectivity there was no definition of any
> > extension in extensions.conf except s at default below is my
> configuration
> > file and
> >
> > output on CLI for your reference.
> >
> >
> > extentions.conf
> > ------------------------------------------------
> > [general]
> > static=yes
> > writeprotect=no
> >
> > [from-sip]
> >
> > [ss7]
> >
> > [default]
> >
> > exten => h,1,Hangup
> >
> >
> > exten => s,1,AGI(extended_test.agi)
> >
> > exten => s,n,NoOp,${CALLERID(all)}
> > exten => s,n,NoOp,${DNID}
> > exten => s,n,NoOp,${CHANNEL}
> >
> > exten => s,n,Answer
> > exten => s,n,Wait(1)
> > exten => s,n(begin),Set(TIMEOUT(digit)=3)
> > exten => s,n,Set(TIMEOUT(response)=10)
> > exten => s,n,Background(mywork/sound_01)
> > exten => hang,1,Hangup
> >
> > [incoming]
> >
> > ------------------------------------------------
> >
> > CLI Output
> > ------------------------------------------------
> >
> > RECIEVED CALLS WHEN DEFAULT EXTIONTIONS DEFINED
> > [Nov 19 16:57:04] DEBUG[26580]: l4isup.c:2466 process_circuit_message:
> > Process circuit message IAM, CIC=7, state=0, reset_done=1
> > -- Recv IAM CIC=7 ANI=77142034884 DNI=6789 RNI= redirect=no/0
> > complete=1
> > [Nov 19 16:57:04] DEBUG[26580]: l4isup.c:2644 process_iam: IAM CIC=7,
> > owner=0x00000000
> > [Nov 19 16:57:04] DEBUG[26580]: l4isup.c:1522 check_iam_sam: Setting
> > iam.dni.complete
> > -- Executing [s at default:1] AGI("**Unknown**", "extended_test.agi")
> in
> > new stack
> >
> > -- Executing [s at default:2] NoOp("**Unknown**", "77142034884") in new
> > stack
> > -- Executing [s at default:3] NoOp("**Unknown**", "unknown") in new
> stack
> > -- Executing [s at default:4] NoOp("**Unknown**", "**Unknown**") in new
> > stack
> >
> > -- Executing [s at default:34] Answer("**Unknown**", "") in new stack
> > [Nov 19 16:57:04] DEBUG[26712]: l4isup.c:1973 ss7_answer: SS7 answer
> CIC=7,
> > pvt->state=1.
> > [Nov 19 16:57:04] DEBUG[26712]: l4isup.c:389 mtp_enqueue_isup_packet:
> Queue
> > packet CIC=7, len=10, linkset='work1', link='l3', slinkset='work1',
> > slink='l1'
> > -- Executing [s at default:35] Wait("**Unknown**", "1") in new stack
> > [Nov 19 16:57:04] DEBUG[26580]: mtp.c:1867 mtp_thread_main: Queue MSU,
> > lsi=0, last_send_ix=0, linkset=work1, m->link=l1
> > [Nov 19 16:57:04] DEBUG[26580]: mtp.c:1575 mtp2_fill_zaptel_buf: Sending
> > buffer to zaptel len=14, on link 'l1' bsn=102, fsn=124.
> > -- Executing [s at default:36] Set("**Unknown**", "TIMEOUT(digit)=3")
> in
> > new stack
> > -- Digit timeout set to 3
> > -- Executing [s at default:37] Set("**Unknown**",
> "TIMEOUT(response)=10")
> > in new stack
> > -- Response timeout set to 10
> > -- Executing [s at default:38] BackGround("**Unknown**", "
> > mywork/sound_01") in new stack
> > [Nov 19 16:57:05] DEBUG[26712]: channel.c:1908 ast_settimeout: Scheduling
> > timer at 160 sample intervals
> > -- Playing ' mywork/sound_01' (language 'en')
> >
> >
> > When I removed the s at default in extension.conf with only the context
> > definition
> >
> > It generates the below output on CLI
> >
> > extentions.conf
> > ------------------------------------------------
> > [general]
> > static=yes
> > writeprotect=no
> >
> > [from-sip]
> >
> > [ss7]
> >
> > [default]
> >
> > [incoming]
> > ------------------------------------------------
> >
> > Output on CLI
> >
> > [Nov 19 16:15:07] DEBUG[26580]: l4isup.c:2466 process_circuit_message:
> > Process circuit message IAM, CIC=6, state=0, reset_done=1
> > -- Recv IAM CIC=6 ANI=77142034884 DNI=6789 RNI= redirect=no/0
> > complete=1
> > [Nov 19 16:15:07] DEBUG[26580]: l4isup.c:2644 process_iam: IAM CIC=6,
> > owner=0x00000000
> > [Nov 19 16:15:07] DEBUG[26580]: l4isup.c:1530 check_iam_sam: Unable to
> > match extension, context: ss7, dni: 6789, rni:
> > [Nov 19 16:15:07] DEBUG[26580]: l4isup.c:389 mtp_enqueue_isup_packet:
> Queue
> > packet CIC=6, len=13, linkset='work1', link='l3', slinkset='work1',
> > slink='l1'
> >
> >
> > When I defined an extension for the dialing code 6789 in SS7 context. It
> > gave the below output on CLI
> >
> > extentions.conf
> > ------------------------------------------------
> > [general]
> > static=yes
> > writeprotect=no
> >
> > [from-sip]
> >
> > [ss7]
> > exten => 6789,1,Goto(my-extension,s,1)
> >
> > [default]
> >
> > [incoming]
> >
> > ------------------------------------------------
> >
> > Error Shown
> >
> > [Nov 19 16:52:28] DEBUG[26580]: l4isup.c:1522 check_iam_sam: Setting
> > iam.dni.complete
> > == Starting **Unknown** at default,s,1 failed so falling back to exten
> > 's' == Starting **Unknown** at default,s,1 still failed so falling back
> to
> > context 'default'
> > [Nov 19 16:52:28] WARNING[26701]: pbx.c:2405 __ast_pbx_run: Channel
> > '**Unknown**' sent into invalid extension 's' in context 'default', but
> no
> > invalid
> >
> > handler
> > [Nov 19 16:52:28] DEBUG[26701]: pbx.c:1621
> > pbx_substitute_variables_helper_full: Function result is '77142034884'
> > [Nov 19 16:52:28] DEBUG[26701]: pbx.c:1621
> > pbx_substitute_variables_helper_full: Function result is 's'
> > [Nov 19 16:52:28] DEBUG[26701]: pbx.c:1621
> > pbx_substitute_variables_helper_full: Function result is 'default'
> > [Nov 19 16:52:28] DEBUG[26701]: pbx.c:1621
> > pbx_substitute_variables_helper_full: Function result is '**Unknown**'
> > -- SS7 hangup '**Unknown**' CIC=7 Cause=0 (state=1)
> > [Nov 19 16:52:28] DEBUG[26701]: l4isup.c:1916 ss7_hangup: SS7 hangup
> > '**Unknown**' CIC=7 (state=1), chan=0x083e9500
> > [Nov 19 16:52:28] DEBUG[26701]: l4isup.c:1947 ss7_hangup: SS7 hangup
> > '**Unknown**' CIC=7 cause=0
> > [Nov 19 16:52:28] DEBUG[26701]: l4isup.c:389 mtp_enqueue_isup_packet:
> Queue
> > packet CIC=7, len=13, linkset='work1', link='l3', slinkset='work1',
> > slink='l1'
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-ss7/attachments/20081121/fe0bad9c/attachment-0001.htm
More information about the asterisk-ss7
mailing list