[asterisk-ss7] Two Asterisk boxes, only ONE signal link

[Patrick Blackman]

Hi Tusar,

I have the same needs. I configured 2 asterisk boxes as a cluster, using 1
signalling link on the first box.
>From the configuration point of view, the cluster is working (there are no
"No signalling links inservice and no cluster receivers alive"" messages).

I configured a third server to simulate the telco equipment. This server has
a TE410p board, but I'm using only 2 E1 trunks, one to each server on the
cluster.

The problem is that, when I place a call to the second cluster server (the
one without the signalling link), the IAM message is sent and an ACM is
received as response. But the server that originated the call says that "ACM
was received but no IAM was sent".

Anyway, this is my ss7.conf file. Hope this can help you.

Regards,
Patrick


[linkset-siuc]
enabled => yes
enable_st => no
use_connect => no
hunting_policy => seq_htl
context => default
language => da
t35 => 15000,timeout
subservice => auto

[link-l3]
linkset => siuc
channels => 1-15,17-31
schannel => 16
firstcic => 1
enabled => yes
echocancel => no
echocan_train => 350
echocan_taps => 128

[link-l4]
linkset => siuc
channels => 1-31
schannel =>
firstcic => 33
enabled => yes
echocancel => no
echocan_train => 350
echocan_taps => 128


[host-AST000012]
enabled => yes
default_linkset => siuc
opc => 0x2
dpc => siuc:0x1
links => l3:1
if-1 => 192.168.0.68

[host-AST000015]
enabled => yes
default_linkset => siuc
opc => 0x2
dpc => siuc:0x1
links => l4:2
if-1 => 192.168.0.61

[cluster]
port => 5040
l4 => AST000012#if-1
l3 => AST000015#if-1

On 4/9/07, Tusar <tusarbd at gmail.com> wrote:
>
> Hi,
>
> I am sorry for writing you again with the same email . But I need this
> feature extremely and  I  believe lots of people in the world are waiting
> for this nice feature .
>
> Could anyone focus on this topics please ?
>
> Best regards,
> ..Tusar..
>
>
>
> ---------- Forwarded message ----------
> From: Tusar <tusarbd at gmail.com >
> Date: Mar 31, 2007 12:57 PM
> Subject: Re: [asterisk-ss7] Two Asterisk boxes, only ONE signal link
> To: asterisk-ss7 at lists.digium.com
>
> Hi,
>
> I am trying to configure using one signaling link with multiple asterisk
> box where I have only one signaling link from Telco company .
>
> Astreisk_1 --> SS7 Signalining --> Telco
>             /
> Astreisk_2--/  ---> Bearer Channel --> Telco
>
> I have patched the "cluster.c" provided from [Anders Baekgaard <
> ab at sifira.dk>] .
>
>
> --- cluster.c~  2006-04-19 09:54:08.000000000 +0200
> +++ cluster.c   2007-03-23 09:51: 25.000000000 +0100
> @@ -847,9 +847,8 @@
>     }
>   }
>
> -  if (this_host->has_signalling_receivers)
> -    if (setup_receiver_socket())
> -      goto fail;
> +  if (setup_receiver_socket())
> +    goto fail;
>   connect_receivers();
>   receivepipe[0] = receivepipe[1] = -1;
>   receivebuf = lffifo_alloc(200000);
>
>
> Asterisk_1 box is running fine and seems "cluster service" is connected
> each other but Asterisk_2 is complaing ..
>
> "Mar 31 12:43:05 NOTICE[9666]: l4isup.c:1076 t22_timeout: T22 timeout (No
> "circuit group reset acknowledge" from peer) CIC=32.
>  Mar 31 12:43:05 WARNING[9666]: mtp.c:1708 mtp_thread_main: No signalling
> links inservice and no cluster receivers alive, dropping packet!
> "
>
> Asterisk_1
> ===========
> *CLI> ss7 cluster status
> receiver Asterisk_1 if 1, addr 192.168.10.17 , c:connected, p:, last try
> 154 msec, 23 fails, 0 forwards
> *CLI>
>
> Asterisk_2
> ===========
> *CLI> ss7 cluster status
> receiver Asterisk_2 if 1, addr 192.168.10.16, c:connected, p:, last try
> 399 msec, 0 fails, 0 forwards
> *CLI>
>
> Here is below my config file for both the box ...
>
> Asterisk_1 [IP:192.168.10.16]
> =======================
>
> [linkset-siuc]
> enabled => yes
> enable_st => no
> use_connect => yes
> hunting_policy => even_mru
> subservice => auto
>
>
> [link-l1]
> linkset => siuc
> channels => 1-15,17-31
> schannel => 16
> firstcic => 1
> enabled => yes
>
>
> [host-Asterisk_1]
> enabled => yes
> default_linkset => siuc
> opc => 0x2
> dpc => siuc:0x1
> if-1 => 192.168.10.17
> links => l1:1
>
>
> [cluster]
> port => 5040
> l1 => Asterisk_2#if-1
>
>
> Asterisk_2 [IP:192.168.10.17]
> ======================
>
> [linkset-siuc]
> enabled => yes
> enable_st => no
> use_connect => no
> hunting_policy => even_mru
> subservice => auto
>
> [link-l2]
> linkset => siuc
> channels => 1-31
> schannel =>
> firstcic => 32
> enabled => yes
>
>
> [host-Asterisk_2]
> enabled => yes
> default_linkset => siuc
> opc => 0x2
> dpc => siuc:0x1
> if-1 => 192.168.10.16
> links => l2:1
>
> [cluster]
> port => 5040
> l2 => Asterisk_1#if-1
>
>
> Could anyone please push me to right direction to sort out this issue
> resolve .
>
>
> Best Regards,
>
> ..Tusar..
>
>
>
> On 3/23/07, Anders Baekgaard <ab at sifira.dk> wrote:
> >
> > Hi Daniel
> >
> > Yes, a "fake" signalling channel is a work aound. The patch below is
> > also a
> > work around..
> >
> > --- cluster.c~  2006-04-19 09:54:08.000000000 +0200
> > +++ cluster.c   2007-03-23 09:51:25.000000000 +0100
> > @@ -847,9 +847,8 @@
> >      }
> >    }
> >
> > -  if (this_host->has_signalling_receivers)
> > -    if (setup_receiver_socket())
> > -      goto fail;
> > +  if (setup_receiver_socket())
> > +    goto fail;
> >    connect_receivers();
> >    receivepipe[0] = receivepipe[1] = -1;
> >    receivebuf = lffifo_alloc(200000);
> >
> > Best regards
> > Anders Baekgaard
> >
> >
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com <http://easynews.com/>--
>
> asterisk-ss7 mailing list
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-ss7
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-ss7/attachments/20070409/be58048c/attachment-0001.htm