[asterisk-commits] res pjsip pubsub: Set the endpoint on SUBSCRIBE dialogs. (asterisk[13])

[SVN commits to the Asterisk project]

Joshua Colp has submitted this change and it was merged.

Change subject: res_pjsip_pubsub: Set the endpoint on SUBSCRIBE dialogs.
......................................................................


res_pjsip_pubsub: Set the endpoint on SUBSCRIBE dialogs.

When SUBSCRIBE dialogs were established, we never associated
the endpoint that created the subscription with the dialog
we end up creating. In most cases, this ended up not causing
any problems.

The actual bug that was observed was that when a device that
was behind NAT established a subscription with Asterisk, Asterisk
would end up sending in-dialog NOTIFY requests to the device's
private IP addres instead of the public address of the NAT router.

When Asterisk receives the initial SUBSCRIBE from the device,
res_pjsip_nat rewrites the contact to the public address on which the
SUBSCRIBE was received. This allows for the dialog to have its target
address set to the proper public address. Asterisk then would send a 200
OK response to the SUBSCRIBE, then a NOTIFY with the initial
subscription state. The device would then send a 200 OK response to
Asterisk's NOTIFY.

Here's where things went wrong. When the 200 OK arrived, res_pjsip_nat
did not rewrite the address in the Contact header. Then, when the PJSIP
dialog layer processed the 200 OK, PJSIP would perform a comparison
between the IP address in the Contact header and its saved target
address for the dialog. Since they differed, PJSIP would update the
target dialog address to be the address in the Contact header. From this
point, if Asterisk needed to send a NOTIFY to the device, the result was
that the NOTIFY would be sent to the private address that the device
placed in the Contact header.

The reason why res_pjsip_nat did not rewrite the address when it
received the 200 OK response was that it could not associate the
incoming response with a configured endpoint. This is because on a
response, the only way to associate the response to an endpoint is by
finding the dialog that the response is associated with and then finding
the endpoint that is associated with that dialog. We do not perform
endpoint lookups on responses. res_pjsip_pubsub skipped the step of
associating the endpoint with the dialog we created, so res_pjsip_nat
could not find the associated endpoint and therefore couldn't rewrite
the contact.

This commit message is like 50x longer than the actual fix.

ASTERISK 24981 #close
Reported by Mark Michelson

Change-Id: I2b963c58c063bae293e038406f7d044a8a5377cd
---
M res/res_pjsip_pubsub.c
1 file changed, 2 insertions(+), 0 deletions(-)

Approvals:
  Joshua Colp: Looks good to me, approved; Verified
  George Joseph: Looks good to me, but someone else must approve



diff --git a/res/res_pjsip_pubsub.c b/res/res_pjsip_pubsub.c
index 0f08a0f..bd40a19 100644
--- a/res/res_pjsip_pubsub.c
+++ b/res/res_pjsip_pubsub.c
@@ -1019,6 +1019,7 @@
 	 * remove the serializer will be successful.
 	 */
 	ast_sip_dialog_set_serializer(sub_tree->dlg, NULL);
+	ast_sip_dialog_set_endpoint(sub_tree->dlg, NULL);
 	pjsip_dlg_dec_session(sub_tree->dlg, &pubsub_module);
 
 	return 0;
@@ -1188,6 +1189,7 @@
 	pjsip_dlg_inc_session(dlg, &pubsub_module);
 	sub_tree->dlg = dlg;
 	ast_sip_dialog_set_serializer(dlg, sub_tree->serializer);
+	ast_sip_dialog_set_endpoint(dlg, sub_tree->endpoint);
 	pjsip_evsub_set_mod_data(sub_tree->evsub, pubsub_module.id, sub_tree);
 }
 

-- 
To view, visit https://gerrit.asterisk.org/166
To unsubscribe, visit https://gerrit.asterisk.org/settings

Gerrit-MessageType: merged
Gerrit-Change-Id: I2b963c58c063bae293e038406f7d044a8a5377cd
Gerrit-PatchSet: 2
Gerrit-Project: asterisk
Gerrit-Branch: 13
Gerrit-Owner: Mark Michelson <mmichelson at digium.com>
Gerrit-Reviewer: George Joseph <george.joseph at fairview5.com>
Gerrit-Reviewer: Joshua Colp <jcolp at digium.com>