[Asterisk-code-review] PJSIP: Remove PJSIP parsing functions from uri length valida... (asterisk[certified/13.1])

[Mark Michelson]

Mark Michelson has uploaded a new change for review.

  https://gerrit.asterisk.org/2645

Change subject: PJSIP: Remove PJSIP parsing functions from uri length validation.
......................................................................

PJSIP: Remove PJSIP parsing functions from uri length validation.

The PJSIP parsing functions provide a nice concise way to check the
length of a hostname in a SIP URI. The problem is that in order to use
those parsing functions, it's required to use them from a thread that
has registered with PJLib.

On startup, when parsing AOR configuration, the permanent URI handler
may not be run from a PJLib-registered thread. Specifically, this could
happen when Asterisk was started in daemon mode rather than
console-mode. If PJProject were compiled with assertions enabled, then
this would cause Asterisk to crash on startup.

The solution presented here is to do our own parsing of the contact URI
in order to ensure that the hostname in the URI is not too long. The
parsing does not attempt to perform a full SIP URI parse/validation,
since the hostname in the URI is what is important.

ASTERISK-25928 #close
Reported by Joshua Colp

Change-Id: Ic3d6c20ff3502507c17244a8b7e2ca761dc7fb60
---
M res/res_pjsip/location.c
1 file changed, 39 insertions(+), 15 deletions(-)


  git pull ssh://gerrit.asterisk.org:29418/asterisk refs/changes/45/2645/1

diff --git a/res/res_pjsip/location.c b/res/res_pjsip/location.c
index 837ade0..bf8307d 100644
--- a/res/res_pjsip/location.c
+++ b/res/res_pjsip/location.c
@@ -272,37 +272,61 @@
 
 int ast_sip_validate_uri_length(const char *contact_uri)
 {
-	pjsip_uri *uri;
-	pjsip_sip_uri *sip_uri;
-	pj_pool_t *pool;
 	int max_length = pj_max_hostname - 1;
+	char *contact = ast_strdupa(contact_uri);
+	char *host;
+	char *at;
+	int theres_a_port = 0;
 
 	if (strlen(contact_uri) > pjsip_max_url_size - 1) {
 		return -1;
 	}
 
-	if (!(pool = pjsip_endpt_create_pool(ast_sip_get_pjsip_endpoint(), "uri validation", 512, 512))) {
-		ast_log(LOG_ERROR, "Unable to allocate pool for uri validation\n");
+	contact = ast_strip_quoted(contact, "<", ">");
+
+	if (!strncmp(contact, "sip:", 4)) {
+		host = contact + 4;
+	} else if (!strncmp(contact, "sips:", 5)) {
+		host = contact + 5;
+	} else {
+		/* Not a SIP URI */
 		return -1;
 	}
 
-	if (!(uri = pjsip_parse_uri(pool, (char *)contact_uri, strlen(contact_uri), 0)) ||
-	    (!PJSIP_URI_SCHEME_IS_SIP(uri) && !PJSIP_URI_SCHEME_IS_SIPS(uri))) {
-		pjsip_endpt_release_pool(ast_sip_get_pjsip_endpoint(), pool);
-		return -1;
+	at = strchr(contact, '@');
+	if (at) {
+		/* sip[s]:user at host */
+		host = at + 1;
 	}
 
-	sip_uri = pjsip_uri_get_uri(uri);
-	if (sip_uri->port == 0) {
+	if (host[0] == '[') {
+		/* Host is an IPv6 address. Just get up to the matching bracket */
+		char *close_bracket;
+
+		close_bracket = strchr(host, ']');
+		if (!close_bracket) {
+			return -1;
+		}
+		close_bracket++;
+		if (*close_bracket == ':') {
+			theres_a_port = 1;
+		}
+		*close_bracket = '\0';
+	} else {
+		/* Host is FQDN or IPv4 address. Need to find closing delimiter */
+		if (strchr(host, ':')) {
+			theres_a_port = 1;
+		}
+		host = strsep(&host, ";:?");
+	}
+
+	if (!theres_a_port) {
 		max_length -= strlen("_sips.tcp.");
 	}
 
-	if (sip_uri->host.slen > max_length) {
-		pjsip_endpt_release_pool(ast_sip_get_pjsip_endpoint(), pool);
+	if (strlen(host) > max_length) {
 		return -1;
 	}
-
-	pjsip_endpt_release_pool(ast_sip_get_pjsip_endpoint(), pool);
 
 	return 0;
 }

-- 
To view, visit https://gerrit.asterisk.org/2645
To unsubscribe, visit https://gerrit.asterisk.org/settings

Gerrit-MessageType: newchange
Gerrit-Change-Id: Ic3d6c20ff3502507c17244a8b7e2ca761dc7fb60
Gerrit-PatchSet: 1
Gerrit-Project: asterisk
Gerrit-Branch: certified/13.1
Gerrit-Owner: Mark Michelson <mmichelson at digium.com>