hello, all of you:<br>i changed to Openvox B200P to test it. but i have no luck for that. the isdnconfig is like this: <br>new-host-3# isdnconfig<br>controller 8 = {<br> Layer 1:<br> description : HFC-4S PCI ISDN adapter<br> type : passive ISDN (Basic Rate, 2xB)<br> channels : 0x3<br> serial : 0xabd5<br> power_save : on<br> dialtone : enabled<br> attached : yes<br> PH-state : F4: Awaiting signal<br> Layer 2:<br> driver_type : DRVR_D_CHANNEL<br>}<br>controller 9 = {<br> Layer 1:<br> description : HFC-4S PCI ISDN adapter<br> type : passive ISDN (Basic Rate,
2xB)<br> channels : 0x3<br> serial : 0xabd6<br> power_save : on<br> dialtone : enabled<br> attached : yes<br> PH-state : F0: Reset<br> Layer 2:<br> driver_type : DRVR_D_CHANNEL<br>}<br>controller 10 = {<br> Layer 1:<br> description : HFC-4S PCI ISDN adapter<br> type : passive ISDN (Basic Rate, 2xB)<br> channels : 0x3<br> serial : 0xabd7<br> power_save : on<br> dialtone : enabled<br> attached : yes<br> PH-state : F0: Reset<br> Layer
2:<br> driver_type : DRVR_D_CHANNEL<br>}<br>controller 11 = {<br> Layer 1:<br> description : HFC-4S PCI ISDN adapter<br> type : passive ISDN (Basic Rate, 2xB)<br> channels : 0x3<br> serial : 0xabd8<br> power_save : on<br> dialtone : enabled<br> attached : yes<br> PH-state : F0: Reset<br> Layer 2:<br> driver_type : DRVR_D_CHANNEL<br>}<br>new-host-3#<br>i also test by run: capitest -u 8 -o 1357XXXXXX.<br>main.c: capi_send_listen_request: sending listen request for incoming_calls<br>main.c: capi_send_listen_request: sending listen request for incoming_calls<br>main.c: capi_send_listen_request: sending listen request for
incoming_calls<br>dialing out, 1 / 1 ...<br>main.c: cd_event: disconnected: user busy<br>i do not know what happen with the card. Could you tell me a right command for isdnconfig for BRI 200P for TE mode? i just want to set all TE mode to test it first. <br>asterisk can start with capi. cable is ok. i do not know why i can not make calls.<br>regards,<br>zhu<br><br><br><b><i>Hans Petter Selasky <hselasky@c2i.net></i></b> 写道：<blockquote class="replbq" style="border-left: 2px solid rgb(16, 16, 255); margin-left: 5px; padding-left: 5px;"> On Thursday 10 January 2008, lizhong zhu wrote:<br>> hello, all of friends:<br>> thanks, Richard Neese. i edit the kernel and add what you gave me and<br>> recompile kernel, the isdn and capi seems work. i run isdnconfig it show s<br>> four contralloer. my card is OpenVox B400P. now asterisk can start and show<br>> : new-host-3*CLI> capi show channels<br>> CAPI thread [0x0] {<br>> Application ID :
0x00000000<br>> Application uptime : 0x00000945 seconds<br>><br>> Call descriptor statistics:<br>> allocation count : 0x00000000 call descriptors<br>> free count : 0x00000000 call descriptors<br>> in memory count : 0x00000000 call descriptors<br>> in use count : 0x00000000 call descriptors<br>> record allocation rate : 0x0000 calls/second<br>> limit allocation rate : 0x0010 calls/second<br>> Currently active calls:<br>> channel name, source->destination, call ID, in/out<br>> }<br>> Config entry 'ISDN2' {<br>> b_channels_curr : 2 call descriptor(s) free<br>> b_channels_max : 2 call descriptor(s) total<br>> }<br>> Config entry 'ISDN1' {<br>> b_channels_curr : 2 call descriptor(s) free<br>> b_channels_max : 2 call descriptor(s) total<br>> }<br>><br>> new-host-3*CLI><br>> i have no idea for capi.conf for BRI. the LEDs
are not blink. i would set<br>> all 4 ports are in TE mode. anyone can tell me some setting for how to<br>> start isdn4bsd and as capi.conf ? thanks!<br>> zhu<br><br>Hi,<br><br>You set the mode using "isdnconfig". What does "isdnconfig" output? The leds <br>are currently not supported.<br><br>You make make testcalls using "capitest".<br><br>--HPS<br></blockquote><br> <p> 
<hr size=1><a href="http://cn.mail.yahoo.com/gc/index.html?entry=5&souce=mail_mailletter_tagline">雅虎邮箱传递新年祝福，个性贺卡送亲朋！</a>