<div>Let me correct that to say that my zaptel.conf file is like this:</div> <DIV><FONT face=Arial size=2></FONT> </DIV> <DIV><FONT face=Arial size=2>fxoks=1</FONT></DIV> <DIV><FONT face=Arial size=2>loadzone=us</FONT></DIV> <DIV><FONT face=Arial size=2>defaultzone=us</FONT></DIV> <div> </div> <div>I changed 2 to 1 as I only have one card...same results. I went through the zapatel setup too but I guess until I get the zaptel part to work and can configure the card with ztcfg it's no use.<BR><BR><B><I>Frank Griffith <glassdude45@yahoo.com></I></B> wrote:</div> <BLOCKQUOTE class=replbq style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #1010ff 2px solid"> <DIV><FONT face=Arial size=2>I run FreeBSD-6.0 and Asterisk-1,2,9,1. I purchased an X100P card and it arrived today. I installed it and to my surprise FreeBSD found it on IRQ9. When I loaded the zaptel drivers this appeared on my monitor:</FONT></DIV> <DIV><FONT face=Arial
size=2></FONT> </DIV> <DIV><FONT face=Arial size=2>Zapata Telephony Interface Registered on major 196<BR>Echo Canceller: MARK3<BR>ZapTel device: vendor=e159 device=1 subvendor=8085<BR>wcfxo0: <Wildcard X101P> port 0x6800-0x68ff mem 0xe4000000-0xe4000fff irq 9 at device 11.0 on pci0<BR>ZapTel Attach for wcfxo0: deviceID : 0xe159<BR>wcfxo0: [FAST]<BR>wcfxo: DAA mode is 'FCC'<BR>Found a Wildcard FXO: Wildcard X101P<BR>ZapTel device loaded.<BR>ztdummy: loaded</FONT></DIV> <DIV><FONT face=Arial size=2></FONT> </DIV> <DIV><FONT face=Arial size=2>I followed the instructions in the Asterisk TFOT manual and did the following to my zaptel.conf file:</FONT></DIV> <DIV><FONT face=Arial size=2></FONT> </DIV> <DIV><FONT face=Arial size=2>fxoks=2</FONT></DIV> <DIV><FONT face=Arial size=2>loadzone=us</FONT></DIV> <DIV><FONT face=Arial size=2>defaultzone=us</FONT></DIV> <DIV><FONT face=Arial size=2></FONT> </DIV> <DIV><FONT face=Arial size=2>I then
restart Asterisk and try to configure the card using zttool. I see two entries, a RED and UNCONFIGURED. No matter which one I choose, it doesn't give me a clue as to what I should do. No man page is available for either zttool or ztcfg. Can anyone offer some advice here. It looks like it's trying to work I just can't get the channel to show up.</FONT></DIV> <DIV> </DIV> <DIV>ztcfg shows 0 channels configured.</DIV> <div> <HR SIZE=1> Stay in the know. Pulse on the new Yahoo.com. <A href="http://us.rd.yahoo.com/evt=42974/*http://www.yahoo.com/preview">Check it out.</A> _______________________________________________<BR>Asterisk-BSD mailing list<BR>Asterisk-BSD@lists.digium.com<BR>http://lists.digium.com/mailman/listinfo/asterisk-bsd<BR></BLOCKQUOTE><BR><p> 
<hr size=1>Do you Yahoo!?<br> Everyone is raving about the <a href="http://us.rd.yahoo.com/evt=42297/*http://advision.webevents.yahoo.com/mailbeta"> all-new Yahoo! Mail.</a>