<!DOCTYPE html PUBLIC '-//W3C//DTD HTML 4.01 Transitional//EN'>
<html>
<head>
<meta http-equiv='Content-Type' content='text/html;charset=us-ascii'>
<style>BODY{font:10pt Tahoma, Verdana, sans-serif;}</style>
</head>
<body>
<DIV>Frank,</DIV>
<DIV> </DIV>
<DIV>'Red is Dead', i.e., RED means that no active PSTN line is detected, for starters. Have you connected an active PSTN line? If so, check your connections or try a different cable.</DIV>
<DIV> </DIV>
<DIV>Once thats done, run zttool, highlight your card, hit F1 and you should see 'no alarms'. If so, you're good to go.</DIV>
<DIV> </DIV>
<DIV>Josh Tipping.</DIV>
<DIV>www.jtcomputers.biz/asterisk/</DIV><BR>
<BLOCKQUOTE style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #0000ff 2px solid; MARGIN-RIGHT: 0px">
<HR>
<B>From:</B> Frank Griffith [mailto:glassdude45@yahoo.com]<BR><B>To:</B> asterisk-bsd@lists.digium.com<BR><B>Sent:</B> Wed, 04 Oct 2006 10:14:40 +1000<BR><B>Subject:</B> [Asterisk-bsd] Can't Configure X100P card<BR><BR>
<DIV><FONT face=Arial size=2>I run FreeBSD-6.0 and Asterisk-1,2,9,1. I purchased an X100P card and it arrived today. I installed it and to my surprise FreeBSD found it on IRQ9. When I loaded the zaptel drivers this appeared on my monitor:</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>Zapata Telephony Interface Registered on major 196<BR>Echo Canceller: MARK3<BR>ZapTel device: vendor=e159 device=1 subvendor=8085<BR>wcfxo0: <Wildcard X101P> port 0x6800-0x68ff mem 0xe4000000-0xe4000fff irq 9 at device 11.0 on pci0<BR>ZapTel Attach for wcfxo0: deviceID : 0xe159<BR>wcfxo0: [FAST]<BR>wcfxo: DAA mode is 'FCC'<BR>Found a Wildcard FXO: Wildcard X101P<BR>ZapTel device loaded.<BR>ztdummy: loaded</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>I followed the instructions in the Asterisk TFOT manual and did the following to my zaptel.conf file:</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>fxoks=2</FONT></DIV>
<DIV><FONT face=Arial size=2>loadzone=us</FONT></DIV>
<DIV><FONT face=Arial size=2>defaultzone=us</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>I then restart Asterisk and try to configure the card using zttool. I see two entries, a RED and UNCONFIGURED. No matter which one I choose, it doesn't give me a clue as to what I should do. No man page is available for either zttool or ztcfg. Can anyone offer some advice here. It looks like it's trying to work I just can't get the channel to show up.</FONT></DIV>
<DIV> </DIV>
<DIV>ztcfg shows 0 channels configured.</DIV>
<P>
<HR SIZE=1>
Stay in the know. Pulse on the new Yahoo.com. <A href="http://us.rd.yahoo.com/evt=42974/*http://www.yahoo.com/preview">Check it out.</A>
<STYLE>
</STYLE>
</BLOCKQUOTE>
<DIV> </DIV>
<DIV> </DIV></body></html>