[Asterisk-bsd] RES: Freebsd 7.3 + DAHDI + TE420
Guillermo Paredes - EDDAS
gparedes at eddas.com.pe
Thu Jul 22 15:36:39 CDT 2010
que te da el comando
ztcfg -vvvvvvvvvvvvvvv
saludos
2010/7/22 Jason Luka - GMAIL Levier <jason.levier at gmail.com>
> asterisk-1.4.29_4
>
>
>
> mas a placa nem dá sinal de sincronização
>
>
>
> *De:* asterisk-bsd-bounces at lists.digium.com [mailto:
> asterisk-bsd-bounces at lists.digium.com] *Em nome de *Guillermo Paredes -
> EDDAS
> *Enviada em:* quinta-feira, 22 de julho de 2010 15:46
> *Para:* Asterisk on BSD discussion
> *Cc:* voip-experts at googlegroups.com;
> asteriskbrasil at listas.asteriskbrasil.org
> *Assunto:* Re: [Asterisk-bsd] Freebsd 7.3 + DAHDI + TE420
>
>
>
> que version asterisk estas usando?
>
> llegas a ver los canales en el cli de asterisk
>
> saludos
>
> 2010/7/21 Jason Luka - GMAIL Levier <jason.levier at gmail.com>
>
> Boa Tarde a todos,
>
>
>
> Alguém já conseguiu utilizar o DAHDI no Freebsd 7.3 com a
> placa Digium TE 420? Estou instalando o sistema operacional do zero e não
> estou conseguindo utilizar a placa, simplemente quando eu levando o DAHDI
> ele reconhece a placa mas me informa que todas as portas estão em status OK
> sem ter nenhum link ligado a mesma.
>
> Segue abaixo o dmesg da hora que o DAHDI levanta:
>
>
>
> Telephony Interface Registered on major 196
>
> Version: 2.3.0-rc2
>
> wct4xxp0: vendor=d161 device=1420 subvendor=5
>
> wct4xxp0: <Wildcard TE420 (5th Gen)> mem 0xdf2fff80-0xdf2fffff irq 41 at
> device 8.0 on pci6
>
> 5th gen card with initial latency of 2 and 1 ms per IRQ
>
> DMA memory base of size 4096 at 0xffffff807be70000. Read:
> 0xffffff807be71000 and Write 0xffffff807be70000
>
> TE4XXP version c01a016d, burst ON
>
> Octasic optimized!
>
> card 0: FALC framer is v3.1.
>
> FALC version: 00000005, Board ID: 00
>
> Reg 0: 0x42a28000
>
> Reg 1: 0x39383000
>
> Reg 2: 0x00000000
>
> Reg 3: 0x00000000
>
> Reg 4: 0x00000001
>
> Reg 5: 0x00000001
>
> Reg 6: 0xc01a016d
>
> Reg 7: 0x00001f00
>
> Reg 8: 0x00000000
>
> Reg 9: 0x00ff0000
>
> Reg 10: 0x0000004a
>
> wct4xxp0: [FILTER+ITHREAD]
>
> wct4xxp0: Enabled 1sec error counter interrupt
>
> wct4xxp0: Enabled errored second interrupt
>
> wct4xxp0: Enabled 1sec error counter interrupt
>
> wct4xxp0: Enabled errored second interrupt
>
> wct4xxp0: Enabled 1sec error counter interrupt
>
> wct4xxp0: Enabled errored second interrupt
>
> wct4xxp0: Enabled 1sec error counter interrupt
>
> wct4xxp0: Enabled errored second interrupt
>
> Found a Wildcard: Wildcard TE420 (5th Gen)
>
> TE4XXP: Launching card: 0
>
> TE4XXP: Setting up global serial parameters
>
> About to enter spanconfig!
>
> Done with spanconfig!
>
> About to enter spanconfig!
>
> Done with spanconfig!
>
> About to enter spanconfig!
>
> Done with spanconfig!
>
> About to enter spanconfig!
>
> Done with spanconfig!
>
> Registered tone zone 0 (United States / North America)
>
> About to enter startup!
>
> TE4XXP: Span 1 configured for CCS/HDB3
>
> 2G: Got interrupt, status = 0000<060>0ScP,A NC I1S: =P r0i0m8a0ry
>
> Swycntc4 xSxopu0r:c eti
>
> ming source auto
>
> wct4xxp0: Evaluating spans for timing source
>
> wct4xxp0: span 1 is green : syncpos 1
>
> wct4xxp0: RCLK source set to span 1
>
> wct4xxp0: Recovered timing mode, RCLK set to span 1
>
> VPM400: Not Present
>
> VPM450: Not Present
>
> Completed startup!
>
> About to enter startup!
>
> 2G: Got interrupt, status = 0004000a, CIS = 0080
>
> <6R>eTgE 45X XiPs: 0S0p0a1n0 020 2co
>
> nfigured for CCS/HDB3
>
> wct4xxp0: timing source auto
>
> wct4xxp0: Evaluating spans for timing source
>
> wct4xxp0: span 1 is green : syncpos 1
>
> wct4xxp0: span 2 is green : syncpos 3
>
> wct4xxp0: RCLK source set to span 1
>
> wct4xxp0: Recovered timing mode, RCLK set to span 1
>
> SPAN 2: Tertiary Sync Source
>
> 2G: Got interrupt, status = 0007000a, CIS = 0080
>
> Reg 5 is 00010102
>
> 2G: Got interrupt, status = 0008000a, <C5I>SV P=M 400008:0 N
>
> otR ePgr e5s einst 0
>
> 0010002
>
> VPM450: Not Present
>
> <6<>62>GC:o mpGloett eidn tsetrarrutputp,! s
>
> ta<t6u>sA b=o ut0 0t0o9 0e0n0tae,r CsItSa r=t u0p0!80
>
>
>
> Reg 5 is 00010102
>
> TE4XXP: Span 3 configured for CCS/HDB3
>
> wct4xxp0: timing source auto
>
> wct4xxp0: Evaluating spans for timing source
>
> wct4xxp0: span 1 is green : syncpos 1
>
> wct4xxp0: span 2 is green : syncpos 3
>
> wct4xxp0: span 3 is green : syncpos 4
>
> wct4xxp0: RCLK source set to span 1
>
> wct4xxp0: Recovered timing mode, RCLK set to span 1
>
> SPAN 3: Quaternary Sync Source
>
> 2G: Got interrupt, status = 000c000b, CIS = 0086
>
> Reg 5 is 00010002
>
> 2G: Got interrupt, status = 000d000a,< 5C>IVSP M=4 0000:8 0No
>
> tR ePgr e5s einst 0
>
> 0010102
>
> VPM450: Not Present
>
> Completed startup!
>
> About to enter startup!
>
> 2G: Got interrupt, status = 000e000a, CIS = 0080
>
> <6R>eTgE 45X XiPs: 0S0p0a1n0 040 2co
>
> nfigured for CCS/HDB3
>
> wct4xxp0: timing source auto
>
> wct4xxp0: Evaluating spans for timing source
>
> wct4xxp0: span 1 is green : syncpos 1
>
> wct4xxp0: span 2 is green : syncpos 3
>
> wct4xxp0: span 3 is green : syncpos 4
>
> wct4xxp0: span 4 is green : syncpos 0
>
> wct4xxp0: RCLK source set to span 1
>
> wct4xxp0: Recovered timing mode, RCLK set to span 1
>
> 2G: Got interrupt, status = 0011000a, CIS = 0080
>
> Reg 5 is 00010102
>
> 2G: Got interrupt, status = 0012000a, <C5I>SV P=M 400008:0 N
>
> oRte gP r5e siesn t00
>
> 010002
>
> VPM450: Not Present
>
> Completed startup!
>
> 2G: Got interrupt, status = 0013000a, CIS = 0080
>
> Reg 5 is 00010102
>
> 2G: Got interrupt, status = 0014000a, CIS = 0080
>
> Reg 5 is 00010002
>
> 2G: Got interrupt, status = 0015000a, CIS = 0080
>
> Reg 5 is 00010102
>
> 2G: Got interrupt, status = 0016000a, CIS = 0080
>
> Reg 5 is 00010002
>
> 2G: Got interrupt, status = 0017000a, CIS = 0080
>
> Reg 5 is 00010102
>
> 2G: Got interrupt, status = 0018000a, CIS = 0080
>
> Reg 5 is 00010002
>
> 2G: Got interrupt, status = 0019000a, CIS = 0080
>
> Reg 5 is 00010102
>
> 2G: Got interrupt, status = 001a000a, CIS = 0080
>
> Reg 5 is 00010002
>
> 2G: Got interrupt, status = 001b000a, CIS = 0080
>
> Reg 5 is 00010102
>
> wct4xxp0: Setting yellow alarm span 1
>
> Master changed to TE4/0/2
>
> wct4xxp0: timing source auto
>
> wct4xxp0: Evaluating spans for timing source
>
> wct4xxp0: span 2 is green : syncpos 3
>
> wct4xxp0: span 3 is green : syncpos 4
>
> wct4xxp0: span 4 is green : syncpos 0
>
> wct4xxp0: RCLK source set to span 2
>
> wct4xxp0: Recovered timing mode, RCLK set to span 2
>
> Need to increase latency. Estimated latency should be 4
>
>
>
> Versão do pacote instalado dahdi-2.3.0rc2.
>
>
>
> Tanto a versão 32bits como a 64bits do sistema operacional apresentam o
> mesmo problema.
>
>
>
> Alguem poderia me dar um caminho a seguir?
>
>
>
> Obrigado a todos pela valiosa atenção.
>
>
>
> Att.
>
> Jason
>
>
> --
> _____________________________________________________________________
> -- Bandwidth and Colocation Provided by http://www.api-digital.com --
>
> Asterisk-BSD mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-bsd
>
>
>
>
> --
> Guillermo Paredes Cornejo - EDDAS
>
> MAIL gparedes at eddas.com.pe
> TEL +51[1]720-7099 x 311 (LIM)
> +51[54]72-0484 x 311 (AQP)
> +1[716]980-0837 x 311 (USA)
> +51[54]958319814 (RPC Claro)
> +51[54]959592141 (Movistar)
> RPM *374564
> WWW www.eddas.com.pe
>
> --
> _____________________________________________________________________
> -- Bandwidth and Colocation Provided by http://www.api-digital.com --
>
> Asterisk-BSD mailing list
> To UNSUBSCRIBE or update options visit:
> http://lists.digium.com/mailman/listinfo/asterisk-bsd
>
--
Guillermo Paredes Cornejo - EDDAS
MAIL gparedes at eddas.com.pe
TEL +51[1]720-7099 x 311 (LIM)
+51[54]72-0484 x 311 (AQP)
+1[716]980-0837 x 311 (USA)
+51[54]958319814 (RPC Claro)
+51[54]959592141 (Movistar)
RPM *374564
WWW www.eddas.com.pe
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-bsd/attachments/20100722/0694ac18/attachment.htm
More information about the Asterisk-BSD
mailing list