[Asterisk-bsd] IRQ or timing problem with HFC-4S

Sun Nov 9 06:26:52 CST 2008

Hello,

Also schrieb Hans Petter Selasky am Sun, Nov 09, 2008 at 01:06:56PM +0100:
> On Sunday 09 November 2008, Oliver Schneider wrote:
> > Also schrieb Hans Petter Selasky am Mon, Oct 13, 2008 at 07:26:11PM +0200:
> > > On Monday 13 October 2008, Oliver Schneider wrote:
> > > > Also schrieb Hans Petter Selasky am Sat, Oct 11, 2008 at 10:29:01AM 
> > > > > On Friday 10 October 2008, Oliver Schneider wrote:
> > > > > > one external EURO ISDN line (normal consumer ISDN line)
> > > > > > one internal ISDN line connected to the HFC-4S in NT mode
> > > > > > Siemens Gigaset 3035 ISDN phone with 3 mobile handsets to HFC-4S
> > > > > Try switching to the version from svn. The tarballs are a little out
> > > > > of date.
> > > Last year, I think I fixed an IRQ lookup related to the S/T statemachine
> > > of the 4S/8S boards from colognechip
> > so I upgraded to
> > Asterisk asterisk-1.4.21.2_3,
> > FreeBSD 7.1-PRELRELEASE
> > isdnconfig - configure ISDN4BSD, version 1.7.0, compiled Oct 17 2008
> > 2008-10-09T14:49:20.792175Z
> > 900
> > hselasky
> >
> > I took the svn version of i4b. I think I still have the same problems,
> > as more DECT handsets are connected to the Gigaset 3035, as more
> > unstable the systems gets.
> >
> > let me know if you need more (and which) debug information.
> 
> I have some ideas.
> Try do some logging:
> isdndecode -u xx -i -o -x > log.file
> "xx" is the controller unit.
> What kind of CPU are you using?
> Are you using USB devices on this machine?
> Are the NT-cables properly terminated by using the resistor switches on the 
> HFC board?

the log file is running. 

I put jupers on the two for this port. Even I cannot find a
documentation for this board. It is from phoneiq in Alabama, US. But the
seller usually replies very fast. 

no USB devices

I have one direct cable from the phone to the board right know (this
config worked on single board very well). With less than 10 meters
cable, the phone has an own power supply.

The CPU is an Transmeta Crusoe 800 Mhz

I will later send you the isdndecode output off list. 

Thanks
Oliver

My dmesg:
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights
reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.1-PRERELEASE #1: Fri Oct 17 00:35:37 UTC 2008
    root at asterisk2.ko.kobo.de:/usr/obj/usr/src/sys/ASTERISK2
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Transmeta(tm) Crusoe(tm) Processor TM5800 (800.04-MHz 586-class
CPU)
  Origin = "GenuineTMx86"  Id = 0x543  Stepping = 3
  Features=0x84893f<FPU,VME,DE,PSE,TSC,MSR,CX8,SEP,CMOV,PN,MMX>
real memory  = 251592704 (239 MB)
avail memory = 232091648 (221 MB)
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413,
RF5413)
acpi0: <INSYDE RSDT_000> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, ef00000 (3) failed
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
acpi_button0: <Power Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff iomem
0xfff80000-0xffffffff on acpi0
pci_link0: BIOS IRQ 10 for 0.16.INTA does not match previous BIOS IRQ 9
pci_link1: BIOS IRQ 10 for 0.16.INTB is invalid
pci0: <ACPI PCI bus> on pcib0
pci0: <memory, RAM> at device 0.1 (no driver attached)
pci0: <memory, RAM> at device 0.2 (no driver attached)
vgapci0: <VGA-compatible display> port 0xe000-0xe07f mem
0xb0000000-0xbfffffff,0xf0000000-0xf003ffff at device 9.0 on pci0
ihfc0: <HFC-4S PCI ISDN adapter> port 0xe080-0xe087 mem
0xf0200000-0xf0200fff irq 9 at device 11.0 on pci0
ihfc0: [ITHREAD]
ihfc0: Attaching I4B controller 8 (PCM slave mode).
ihfc0: Attaching I4B controller 9 (PCM slave mode).
ihfc0: Attaching I4B controller 10 (PCM slave mode).
ihfc0: Attaching I4B controller 11 (PCM slave mode).
ihfc0: Creating /dev/ihfc8.X.
ihfc0: Creating /dev/ihfc9.X.
ihfc0: Creating /dev/ihfc10.X.
ihfc0: Creating /dev/ihfc11.X.
uhci0: <VIA 83C572 USB controller> port 0x1200-0x121f irq 9 at device
16.0 on pci0
uhci0: [ITHREAD]
uhci0: LegSup = 0x8030
usb0: <VIA 83C572 USB controller> on uhci0
uhci1: <VIA 83C572 USB controller> port 0x1220-0x123f irq 9 at device
16.1 on pci0
uhci1: [ITHREAD]
uhci1: LegSup = 0x8030
usb1: <VIA 83C572 USB controller> on uhci1
uhci2: <VIA 83C572 USB controller> port 0x1240-0x125f irq 10 at device
16.2 on pci0
uhci2: [ITHREAD]
uhci2: LegSup = 0x8030
usb2: <VIA 83C572 USB controller> on uhci2
ehci0: <VIA VT6202 USB 2.0 controller> irq 10 at device 16.3 on pci0
ehci0: [ITHREAD]
usb3: EHCI version 1.0
usb3: <VIA VT6202 USB 2.0 controller> on ehci0
isab0: <PCI-ISA bridge> at device 17.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 8235 UDMA133 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1100-0x110f at device 17.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pci0: <multimedia, audio> at device 17.5 (no driver attached)
vr0: <VIA VT6102 Rhine II 10/100BaseTX> port 0xe200-0xe2ff mem
0xf0201000-0xf02010ff irq 9 at device 18.0 on pci0
vr0: Quirks: 0x0
vr0: Revision: 0x74
miibus0: <MII bus> on vr0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vr0: Ethernet address: 00:90:dc:04:0e:ce
vr0: [ITHREAD]
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on
acpi0
sio0: type 16550A
sio0: [FILTER]
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
sio1: [FILTER]
cpu0: <ACPI CPU> on acpi0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xcffff,0xe0000-0xe1fff pnpid
ORM0000 on isa0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
ppbus0: [ITHREAD]
plip0: <PLIP network interface> on ppbus0
plip0: WARNING: using obsoleted IFF_NEEDSGIANT flag
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ppc0: [GIANT-LOCKED]
ppc0: [ITHREAD]
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
isa0
Timecounter "TSC" frequency 800037953 Hz quality 800
Timecounters tick every 1.000 msec
i4bctl: ISDN system control port attached
capi: CAPI call control device attached, v2.11
i4b: ISDN call control device attached
i4btrc: 64 ISDN trace device(s) attached
i4brbch: 8 raw B channel access device(s) attached
i4btel: 8 ISDN telephony interface device(s) attached
i4bipr: 8 IP over raw HDLC ISDN device(s) attached
i4bisppp: 8 ISDN SyncPPP device(s) attached
usb0: 12Mbps Full Speed USB v1.0
uhub0: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 2 ports with 2 removable, self powered
usb1: 12Mbps Full Speed USB v1.0
uhub1: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 2 ports with 2 removable, self powered
usb2: 12Mbps Full Speed USB v1.0
uhub2: <VIA UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
usb3: 480Mbps High Speed USB v2.0
uhub3: <VIA EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usb3
uhub3: 6 ports with 6 removable, self powered
ad2: 3871MB <CF 4GB 20070312> at ata1-master PIO4
Trying to mount root from ufs:/dev/ad2s1a
i4b: unit 8, assigned TEI = 227 = 0xe3
i4b: unit 8, assigned TEI = 229 = 0xe5